SHIFT LEVER REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HNV0

      Disengage the 10 claws and remove the front door scuff plate LH.

  5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01HPCC

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HOQS

      Disconnect the front door opening trim weatherstrip LH.

  7. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01HO7A

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HQ0A

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01HOBK

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HQQ4

      Remove the bolt <B> and screw <C> or <D>.

    2. A01HPRH

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  10. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01HO23

      Disconnect the front door opening trim weatherstrip RH.

  13. REMOVE INSTRUMENT SIDE PANEL RH


    1. A01HOT8

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HP2C

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  14. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01HMT9

      Disengage the 4 claws.

    2. Disengage the 2 guides to remove the No. 2 instrument panel under cover sub-assembly.

  15. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01HNRV

      Remove the 3 bolts.

    4. A01HNQT

      Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. A01HN9PE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01HOBP

      Remove the 2 screws <C> or <D>.

    2. Open the lower instrument panel door.

    3. A01HR3C

      Remove the 3 screws <C> or <D>.

    4. A01HQ9V

      Disengage the 2 clips and guide.

    5. A01HOXQ

      Disengage the glove compartment light as shown in the illustration.

    6. Disconnect each connector and remove the lower instrument panel sub-assembly.

  17. REMOVE BOX BOTTOM MAT


    1. A01HMY5

      Remove the box bottom mat.

  18. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01HOHW

      Remove the 2 screws <C> or <D>.

    2. A01HNXD

      Disengage the 4 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  19. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01HQ1M

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01HOYZ

      Remove the 2 screws <C> or <D>.

    3. A01HR29

      Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.

  20. REMOVE CONSOLE BOX INSERT


    1. A01HMKE

      Remove the 2 screws <C> or <D>.

    2. A01HME7

      Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.

  21. REMOVE FLOOR CARPET BRACKET LH


    1. A01HQXF

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  22. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET


    1. A01HMIE

      Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.

  23. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01HMB1

      Remove the clip and No. 1 console box duct.

  24. REMOVE LOWER SHIFT LEVER ASSEMBLY


    1. Move the shift lever to N.

    2. A01HQ55

      Disconnect the end of transmission control cable assembly from the lower shift lever assembly.

    3. Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.

    4. A01HNB4

      Disconnect the 3 clamps and 2 connectors.

    5. A01HP9T

      Remove the 4 bolts and lower shift lever assembly.

  25. REMOVE SHIFT LEVER SUPPORT


    1. A01HQ6Y

      Remove the 4 bolts and shift lever support.