SFI SYSTEM, Diagnostic DTC:P2009, P2010

DTC Code DTC Name
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
P2010 Intake Manifold Runner Control Circuit High (Bank 1)

DESCRIPTION

The ECM activates the intake air control valve actuator (for tumble control valve), which opens and closes the Tumble Control Valve (TCV). The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.

DTC No. DTC Detection Condition Trouble Area
P2009

Both of the following conditions continue for 1 second (1 trip detection logic).

(a) The output duty of the intake air control valve actuator is 100% or higher.

(b) The current of the intake air control valve actuator is less than 0.35 A.

  • Open or short in intake air control valve actuator (for tumble control valve) circuit

  • Intake air control valve actuator (for tumble control valve)

  • Intake manifold

  • ECM
P2010

Either of the following conditions continues for 6 times or more (1 trip detection logic).

(a) The motor drive IC has overcurrent.

(b) The motor drive IC failure.

  • Open or short in intake air control valve actuator (for tumble control valve) circuit

  • Intake air control valve actuator (for tumble control valve)

  • Intake manifold

  • ECM

MONITOR DESCRIPTION

When the voltage of the intake air control valve actuator deviates from the standard range, the ECM determines that a malfunction has occurred and stores a DTC.

MONITOR STRATEGY

Related DTCs

P2009: Intake air control valve actuator for tumble control valve range check (low current)

P2010: Intake air control valve actuator for tumble control valve range check (high current)
Required Sensors/Components (Main) Intake air control valve actuator (for tumble control valve)
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration

1 second: P2009

6 times: P2010
MIL Operation Immediate
Sequence Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None
P2009
All of the following conditions are met -
Battery voltage 8 V or higher
Ignition switch ON
Starter Off
Output duty cycle 100% or higher
Difference between motor current and previous motor current Less than 0.2 A
P2010
All of the following conditions are met -
Battery voltage 8 V or higher
Ignition switch ON
Starter Off

TYPICAL MALFUNCTION THRESHOLDS

P2009
Intake air control valve actuator for tumble control valve current Less than 0.35 A
P2010
Motor driver IC high current limiter monitor input Fail

COMPONENT OPERATING RANGE

P2009
Intake air control valve actuator for tumble control valve current Higher than 0.35 A
P2010
Motor driver IC high current limiter monitor input Pass

CONFIRMATION DRIVING PATTERN


  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the ignition switch off and wait for at least 30 seconds.

  6. Turn the ignition switch to ON and turn the Techstream on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  8. Check that the engine coolant temperature is 60°C (140°F) or higher.

  9. Wait approximately 10 seconds.

  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  13. Input the DTC: P2009 or P2010.

  14. Check the DTC judgment result.

    Techstream Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

  15. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs Click here.

    Tech Tips


    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

WIRING DIAGRAM

Refer to DTC P2004 Click here.

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)


    1. Inspect the intake air control valve actuator (for tumble control valve) Click here.


    NG

    REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE) Click here

    OK

  2. INSPECT INTAKE MANIFOLD (TUMBLE CONTROL VALVE OPERATION)


    1. Inspect the intake manifold for the tumble control valve operation Click here.


    NG

    REPLACE INTAKE MANIFOLD Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)


    1. Disconnect the ECM connector.

    2. Disconnect the intake air control valve actuator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Y4-4 (M-) - E26-21 (IA1-) Always Below 1 Ω
      Y4-5 (M+) - E26-22 (IA1+) Always Below 1 Ω
      Y4-4 (M-) or E26-21 (IA1-) - Body ground Always 10 kΩ or higher
      Y4-5 (M+) or E26-22 (IA1+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2009 OR P2010)


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the Techstream on.

    8. Wait approximately 10 seconds.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.

      Result
      Result Proceed to
      DTC P2009 or P2010 is output A
      DTC is not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

    REPLACE ECM Click here