OIL PUMP REMOVAL


  1. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

    Click here

  2. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    1. A01HMEXE01

      Using SST, hold the crankshaft pulley.

      SST
      09213-70011   ( 09213-70020 )
      09330-00021
    2. A01HQGI

      Remove the 8 bolts, front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer.

  3. INSTALL ENGINE ON ENGINE STAND


    1. Install the engine onto an engine stand with the bolts.

  4. REMOVE ENGINE HANGERS


    1. A01HQVUE18
      Text in Illustration
      *1 No. 1 engine hanger
      *2 No. 2 engine hanger
      *a Bank 1
      *b Bank 2

      Remove the 4 bolts and 2 engine hangers.

  5. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    1. A01HPESE01
      Text in Illustration
      *A Type A
      *B Type B

      Disconnect the ventilation hose.

    2. Disconnect the hose clamp and union to check valve hose.

    3. A01HQBW

      Disconnect the connector and wire harness clamp.

    4. Disconnect the 2 water by-pass hoses and fuel vapor feed hose.

    5. A01HN11

      Disconnect the connector from the intake air control valve assembly.

    6. A01HNA5

      Remove the bolt and vacuum hose clamp.

    7. A01HPSN

      Remove the bolt and separate the throttle body bracket from the intake air surge tank assembly.

    8. A01HMGP

      Remove the bolt and separate the No. 1 surge tank stay from the intake air surge tank assembly.

    9. A01HPA4

      Remove the 2 nuts from the intake air surge tank assembly.

    10. Using a 5 mm socket hexagon wrench, remove the 4 bolts.

    11. A01HOYW

      Remove the intake air surge tank assembly and 3 gaskets.

  6. REMOVE NO. 1 SURGE TANK STAY


    1. A01HPJF

      Remove the bolt and No. 1 surge tank stay.

  7. REMOVE THROTTLE BODY BRACKET


    1. A01HMUX

      Remove the bolt and throttle body bracket.

  8. REMOVE IGNITION COIL ASSEMBLY


    1. A01HOHL

      Remove the nut.

    2. Disconnect the 2 harness clamps.

    3. A01HNCI

      Disconnect the 6 ignition coil connectors.

    4. A01HN3I

      Remove the 6 bolts and 6 ignition coils.

  9. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    1. A01HP8S

      Uniformly loosen and remove the 6 nuts.

    2. Remove the exhaust manifold sub-assembly RH and gasket.

  10. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE


    1. A01HO81

      Remove the oil level dipstick.

    2. Remove the bolt and No. 2 engine oil level dipstick guide.

    3. A01HR2F

      Remove the O-ring from the No. 2 engine oil level dipstick guide.

  11. REMOVE NO. 2 MANIFOLD STAY


    1. A01HN7B

      Remove the bolt, nut and No. 2 manifold stay.

  12. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    1. A01HP8V

      Remove the 3 bolts and No. 2 exhaust manifold heat insulator.

  13. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    1. A01HNEM

      Uniformly loosen and remove the 6 nuts.

    2. Remove the exhaust manifold assembly LH and gasket.

  14. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    1. A01HQU1

      Remove the 5 bolts and V-ribbed belt tensioner assembly.

  15. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. A01HNO4

      Remove the bolt and engine oil level dipstick guide.

    2. A01HNLR

      Remove the O-ring.

  16. REMOVE NO. 2 TIMING GEAR COVER


    1. A01HO1B

      Remove the 2 bolts and No. 2 timing gear cover.

  17. REMOVE WATER PUMP PULLEY


    1. A01HQGPE01

      Using SST, hold the water pump pulley.

      SST
      09960-10010   ( 09962-01000, 09963-00700 )

    2. Remove the 4 bolts and water pump pulley.

  18. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    1. A01HOL7

      Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley sub-assembly and idler pulley cover plate.

  19. REMOVE NO. 1 VACUUM SWITCHING VALVE


    1. A01HMDT

      Remove the bolt and No. 1 vacuum switching valve.

  20. REMOVE CRANK POSITION SENSOR


    1. A01HR2S

      Disconnect the crank position sensor connector.

    2. Remove the bolt and crank position sensor.

  21. REMOVE NO. 1 OIL PIPE


    1. A01HMSPE02
      Text in Illustration
      *1 Oil Pipe Union

      Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.

    2. Remove the oil control valve filter LH and gaskets.

  22. REMOVE OIL PIPE


    1. A01HOR1E04
      Text in Illustration
      *1 Oil Pipe Union
      *2 Bolt

      Remove the bolt.

    2. Remove the 2 oil pipe unions and oil pipe.

    3. Remove the oil control valve filter RH and gaskets.

  23. REMOVE CRANKSHAFT PULLEY


    1. A01HP3SE03
      Text in Illustration
      *a Hold
      A01HNYE Turn

      Using SST, loosen the crankshaft pulley bolt.

      SST
      09213-70011   ( 09213-70020 )
      09330-00021
    2. A01HNBLE01
      Text in Illustration
      *a Hold
      A01HNYE Turn

      Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )
    3. A01HQOU

      Remove the pulley set key from the crankshaft.

  24. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH


    1. A01HOX3

      Remove the 6 bolts and No. 1 front engine mounting bracket LH.

    2. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.

  25. REMOVE WATER INLET HOUSING


    1. A01HOZTE03
      Text in Illustration
      *1 Water hose
      *2 Water Inlet housing

      Disconnect the water hose.

    2. Remove the 2 bolts, nut and water inlet housing.

    3. A01HNTI

      Remove the 2 O-rings.

  26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    1. A01HNOZ

      Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.

    2. A01HQ46

      Remove the 3 gaskets.

  27. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    1. A01HPOIE05
      Text in Illustration
      *1 Baffle Plate

      Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.

      Note

      The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly LH.

    2. A01HMQ6

      Remove the 3 gaskets.

  28. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    1. A01HQYZE02
      Text in Illustration
      *1 Nut

      Remove the 16 bolts and 2 nuts.

    2. A01HR3H

      Insert the blade of the oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

      Note

      Be careful not to damage the contact surfaces of the oil pans.

    3. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.

  29. REMOVE OIL STRAINER SUB-ASSEMBLY


    1. A01HQWUE03
      Text in Illustration
      *1 Bolt
      *2 Nut

      Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.

    2. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.

  30. REMOVE OIL PAN SUB-ASSEMBLY


    1. A01HN0JE03
      Text in Illustration
      *1 Nut

      Remove the 16 bolts and 2 nuts.

      Tech Tips

      Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

    2. A01HPZPE02
      Text in Illustration
      *1 Protective Tape

      Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder block and oil pan.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01HN5G

      Remove the 2 O-rings.

    4. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.

  31. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    1. A01HMZQE01
      Text in Illustration
      *1 Nut

      Remove the 23 bolts and 2 nuts shown in the illustration.

    2. A01HQFKE03
      Text in Illustration
      *1 Protective Tape

      Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01HOKJE01

      Remove the gasket.

  32. REMOVE TIMING CHAIN CASE OIL SEAL


    1. A01HPB8E05
      Text in Illustration
      *1 Protective Tape
      *2 Wooden Block

      Using a screwdriver and wooden block, pry out the oil seal.

      Tech Tips

      Tape the screwdriver tip before use.