CYLINDER HEAD GASKET REMOVAL


  1. REMOVE CAMSHAFT

    Click here

  2. REMOVE NO. 2 CAMSHAFT


    1. Remove the No. 2 camshaft.

  3. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    1. A01HQ7VE02
      Text in Illustration
      *1 Protective Tape

      Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)


    1. A01HMWTE07
      Text in Illustration
      *1 Pin
      *2 Plunger
      *a Push

      While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 3 chain tensioner assembly.

    2. A01HNAKE06
      Text in Illustration
      *a Turn
      *b Hold

      Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.

      SST
      09922-10010

      Note


      • Be careful not to damage the cylinder head with SST.

      • Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

    3. Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.

  5. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    1. A01HMOS

      Remove the bolt and No. 3 chain tensioner assembly.

  6. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


    1. A01HR2OE06
      Text in Illustration
      *1 Knock Pin
      *a Front View

      Check that the camshafts are positioned as shown in the illustration.

    2. A01HPLBE03

      Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

    3. A01HO3PE01

      Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

      Note

      Uniformly loosen the bolts while keeping the camshaft level.

    4. Remove the 5 camshaft bearing caps.

  7. REMOVE NO. 3 CAMSHAFT


    1. Remove the No. 3 camshaft.

  8. REMOVE NO. 4 CAMSHAFT


    1. Remove the No. 4 camshaft.

  9. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    1. A01HOH8E02
      Text in Illustration
      *1 Protective Tape

      Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    1. Remove the 24 valve rocker arms.

      Tech Tips

      Arrange the removed parts in the correct order.

  11. REMOVE VALVE LASH ADJUSTER ASSEMBLY


    1. Remove the 24 valve lash adjuster assemblies from the cylinder head.

      Tech Tips

      Arrange the removed parts in the correct order.

  12. REMOVE VALVE STEM CAP


    1. Remove the 24 valve stem caps.

  13. REMOVE WATER OUTLET


    1. A01HR4QE02
      Text in Illustration
      *1 Nut
      *2 Bolt

      Remove the 2 bolts, 4 nuts and water outlet.

    2. A01HQLT

      Remove the 2 gaskets and O-ring.

  14. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH


    1. A01HNRWE01

      Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

      Note


      • Be careful not to drop washers into the cylinder head sub-assembly.

      • Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

      Tech Tips

      Arrange the removed parts in the correct order.

    2. Remove the cylinder head sub-assembly RH.

  15. REMOVE CYLINDER HEAD GASKET RH


    1. Remove the cylinder head gasket RH.

  16. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH


    1. A01HNTZE01

      Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.

    2. A01HQVBE01

      Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

      Note


      • Be careful not to drop washers into the cylinder head sub-assembly.

      • Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

      Tech Tips

      Be sure to keep separate the removed parts for each installation position.

    3. Remove the cylinder head sub-assembly LH.

  17. REMOVE CYLINDER HEAD GASKET LH


    1. Remove the cylinder head gasket LH.