Click here

УЗЕЛ ТОПЛИВНОГО БАКА СНЯТИЕ

Click here
Click here
  1. Click here

    DISCHARGE FUEL SYSTEM PRESSURE

    CAUTION:

    • Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

    • After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.


    1. Disconnect the fuel pump ECU connector (Click here).

    2. Start the engine. After the engine stops, turn the engine switch off.

      Tip:

      DTC P0171/0174 (system too lean) may be stored.

    3. Crank the engine again, and then check that the engine does not start.

    4. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:
      • w/ Navigation System:

        After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    6. Connect the fuel pump ECU connector (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:
    • w/ Navigation System:

      After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE SPARE TIRE

  4. Click here

    REMOVE TAILPIPE ASSEMBLY


    1. A01ENAH

      Выверните болт и снимите зажим выхлопной трубы.

    2. Снимите 2 опоры выпускной трубы, прокладку и выхлопную трубу.

  5. Click here

    REMOVE SPARE WHEEL CARRIER CROSSMEMBER AND SPARE WHEEL CARRIER BRACKET


    1. A01ESJHE01

      Remove the bolt labeled A, and then loosen the 4 bolts labeled B.

    2. Slightly raise the spare wheel carrier crossmember, and then remove the 6 bolts labeled C, spare wheel carrier crossmember and 2 brackets.

  6. Click here

    REMOVE NO. 1 SPARE WHEEL STOPPER


    1. A01EQAG

      Remove the 2 bolts and spare wheel stopper.

  7. Click here

    REMOVE FUEL TANK CAP ASSEMBLY

  8. Click here

    DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY


    1. A01EPX4

      Disconnect the 2 fuel tank evaporation vent tubes.

  9. Click here

    DISCONNECT FUEL HOSE

  10. Click here

    DISCONNECT FUEL TANK BREATHER HOSE


    1. A01EOIM

      Disconnect the breather hose from the filler pipe.

  11. Click here

    DISCONNECT NO. 3 FUEL HOSE


    1. A01ENIB

      Disconnect the fuel hose from the filler pipe.

  12. Click here

    DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    1. A01ES2O

      Disconnect the hose from the filler pipe.

  13. Click here

    REMOVE FUEL SUB TANK SUB-ASSEMBLY


    1. A01EOLY

      Disconnect the floor No. 3 wire connector.

    2. Using a clip remover, detach the 3 wire harness clamps.

    3. Set an engine lifter underneath the fuel sub tank.

    4. A01ERZA

      Remove the 2 bolts and disconnect the 2 fuel tank bands.

    5. Remove the fuel sub tank.

  14. Click here

    REMOVE FLOOR NO. 3 WIRE


    1. A01EQ06

      Disconnect the sender gauge connector.

    2. Using a clip remover, detach the wire harness clamp.

  15. Click here

    REMOVE FUEL SENDER GAUGE ASSEMBLY


    1. A01EQU1

      Remove the 5 screws and sender gauge.

      Note:

      Be careful not to bend the arm of the fuel sender gauge.

    2. Remove the gasket from the sender gauge.

  16. Click here

    REMOVE FUEL HOSE

  17. Click here

    REMOVE FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY


    1. A01ERO7

      Remove the 2 fuel tank evaporation vent tubes.

  18. Click here

    REMOVE FUEL AND EVAPORATION VENT TUBE SUB-ASSEMBLY


    1. A01EO78

      Remove the 6 bolts and the fuel and evaporation vent tube.

    2. Remove the gasket from the fuel and evaporation vent tube.

  19. Click here

    REMOVE FUEL TANK BREATHER HOSE


    1. A01ERN1

      Remove the breather hose from the fuel sub tank.

  20. Click here

    REMOVE NO. 3 FUEL HOSE


    1. A01EOL5

      Remove the fuel hose from the fuel sub tank.

  21. Click here

    REMOVE FUEL TANK TO FILLER PIPE HOSE


    1. A01EO8U

      Remove the hose from the fuel sub tank.