REAR DOOR WINDOW FRAME MOULDING INSTALLATION


  1. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING


    1. A0160TC

      Engage the 2 clips and install the rear door upper window frame moulding to the door frame.

    2. Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 6 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note

      A0160NQE01

      • Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A01630SE01

        Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

      • A015YRBE01

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

  2. INSTALL REAR DOOR WEATHERSTRIP


    1. A015ZUM

      Engage the 23 clips.

    2. Install the rear door weatherstrip with the double-sided tape.

  3. INSTALL REAR DOOR FRAME GARNISH


    1. A015ZLW

      Install the door frame garnish with the 2 clips.

  4. INSTALL REAR DOOR TRIM COVER


    1. A0160LL

      Engage the 5 clips to install the rear door trim cover.

    2. Install the screw.

  5. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A0161ZA

      Engage the 3 claws to install the rear door inner glass weatherstrip.

  6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install the 2 rear door trim board retainers (green).

    2. A016170

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear inside handle.

    3. Connect each connector.

    4. A0162P8

      Engage the rear door trim board with the 3 clips of the rear door inner glass weatherstrip.

    5. A015ZS2

      Engage the 8 clips to install the rear door trim board to the rear door panel.

    6. Install the 2 screws.

  7. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A015Z2B

      Engage the 2 claws and 2 clips, and install the rear power window regulator switch assembly with rear door armrest base panel.

  8. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A0162FH

      Engage the 3 claws to install the rear door inside handle bezel plug.

  9. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

    Tech Tips

    When installing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body and rear door front window frame moulding excessively.


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Clean the rear door front window frame moulding (if reusing the rear door front window frame moulding).


      1. Using a heat light, heat the rear door front window frame moulding.

      2. Remove the double-sided tape from the rear door front window frame moulding.

      3. Wipe off any tape adhesive residue with cleaner.

      4. Apply new double-sided tape to the rear door front window frame moulding.

    3. A0160M7

      Install the rear door front window frame moulding.


      1. Using a heat light, heat the vehicle body and rear door front window frame moulding.

      2. Remove the peeling paper from the face of the rear door front window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Install the rear door front window frame moulding with the clip.

  10. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A0161WY

      Engage the 5 clips and install the rear door belt moulding assembly.