FRONT DOOR WINDOW FRAME MOULDING INSTALLATION


  1. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING


    1. A0162B3

      Engage the front door upper window frame moulding to the door frame.

    2. Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note

      A0160NQE01

      • Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A01630SE01

        Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

      • A015YRBE01

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

  2. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

    Tech Tips

    When installing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body and front door rear window frame moulding excessively.


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Clean the front door rear window frame moulding (if reusing the front door rear window frame moulding).


      1. Using a heat light, heat the front door rear window frame moulding.

      2. Remove the double-sided tape from the front door rear window frame moulding.

      3. Wipe off any tape adhesive residue with cleaner.

      4. Apply new double-sided tape to the front door rear window frame moulding.

    3. A015YTO

      Install the front door rear window frame moulding.


      1. Using a heat light, heat the vehicle body and front door rear window frame moulding.

      2. Remove the peeling paper from the face of the front door rear window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Install the front door rear window frame moulding with the clip.

  3. INSTALL FRONT DOOR WEATHERSTRIP


    1. A015ZNX

      Engage the 21 clips.

    2. Install the front door weatherstrip with the double-sided tape.

  4. INSTALL DOOR FRAME GARNISH


    1. A0161KQ

      Install the door frame garnish with the 2 clips.

  5. INSTALL FRONT DOOR TRIM COVER


    1. A016263

      Engage the 6 clips to install the front door trim cover.

    2. Install the screw.

  6. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    1. A0161IB

      Engage the 7 clips and install the front door belt moulding assembly.

  7. INSTALL FRONT DOOR FRAME COVER


    1. A0160ZK

      Install the front door frame cover with the nut.

  8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A0161HF

      Engage the 4 claws and install the front door inner glass weatherstrip.

  9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install 2 new front door trim board retainers (green).

    2. A01630D

      Connect the front door lock remote control cable and front door inside locking cable to the front inside handle.

    3. Connect each connector.

    4. A01614A

      Engage the front door trim board with the 4 clips of the front door inner glass weatherstrip.

    5. A0160MG

      Engage the 9 clips and install the front door trim board to the front door panel.

    6. Install the 2 screws.

  10. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A0160WE

      Engage the claw and install the courtesy light assembly.

  11. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. Connect each connector.

    2. A015YVS

      Engage the 3 claws and 2 clips, and install the power window regulator master switch assembly with front door armrest base panel.

  12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01613G

      Engage the 3 claws and install the front door inside handle bezel plug.