HEADLIGHT DIMMER SWITCH REMOVAL


  1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A015ZUQ

      Disengage the claw and remove the lower No. 3 steering wheel cover.

  4. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A0160QU

      Disengage the claw and remove the lower No. 2 steering wheel cover.

  5. REMOVE STEERING PAD


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A0163J9E01

      Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    4. A0161J5

      Pull out the steering pad from the steering wheel assembly.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    5. Disconnect the horn connector from the steering pad.

    6. Disconnect the 2 airbag connectors and remove the steering pad.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

  6. REMOVE STEERING WHEEL ASSEMBLY


    1. A015YNDE01

      Remove the steering wheel assembly set nut.

    2. Put matchmarks on the steering wheel assembly and the steering main shaft.

    3. Disconnect the connectors from the spiral cable.

    4. A0160D7E01

      Install SST to the steering wheel assembly as shown in the illustration.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

      Note

      Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

    5. A015Z1YE01

      Using SST, remove the steering wheel assembly.

  7. REMOVE STEERING COLUMN COVER


    1. A0160S7

      Remove the 3 screws.

    2. A0162IK

      Disengage the 2 claws to remove the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    3. A015YO2

      Disengage the claw.

    4. A015YPR

      Disengage the 4 clips and 2 guides to separate the upper steering column cover.

  8. REMOVE SPIRAL CABLE WITH STEERING ANGLE SENSOR


    1. A0160H7E01

      Disconnect the connectors from the spiral cable with steering angle sensor.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

    2. Disengage the 3 claws and remove the spiral cable with steering angle sensor.

  9. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY


    1. A01606T

      Disconnect the 2 connectors.

    2. Disengage the claw and remove the windshield wiper switch assembly as shown in the illustration.

      Note

      If the claw is pushed with excessive force, it may break.

  10. REMOVE TILT AND TELESCOPIC SWITCH


    1. A0163FB

      Disconnect the connector.

    2. Disengage the claw and pull out the tilt and telescopic switch.

      Note

      Pushing on the claw too hard will break the claw.

  11. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY


    1. A0162A4

      Disconnect the connector.

    2. Disengage the clamp and claw as shown in the illustration.

    3. A015YO0

      Remove the headlight dimmer switch assembly as shown in the illustration.