WASHER MOTOR REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01638L

      Using a clip remover, remove the 9 clips and cool air intake duct seal.

  3. REMOVE ENGINE ROOM SIDE COVER LH (for LHD)


    1. A016120

      Remove the 5 clips and engine room side cover LH.

  4. REMOVE ENGINE ROOM SIDE COVER LH (for RHD)


    1. A015Z63

      Remove the 4 clips and engine room side cover LH.

  5. REMOVE FRONT UPPER FENDER PROTECTOR LH


    1. A0162I4

      Separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.

    2. Disengage the 4 clips and the claw to remove the front upper fender protector LH.

  6. REMOVE RADIATOR GRILLE PROTECTOR


    1. A01623G

      Remove the 2 radiator grille protectors.

  7. REMOVE FRONT BUMPER ASSEMBLY


    1. A0162OR

      Using a screwdriver, turn the pins 90 degrees and remove the 2 pin hold clips.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for the RH side and LH side.

    2. A0162S2

      remove the screw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. A0163H6E01

      Put protective tape around the front bumper assembly.

    4. Remove the 8 screws.

    5. A0161S5

      Using a clip remover, remove the 2 clips and screw.

    6. A01617S

      Disengage the 10 claws and disconnect the front bumper assembly as shown in the illustration.

    7. w/ LEXUS Parking Assist-Sensor system:


      1. Disconnect the ultrasonic sensor connector.

    8. Disconnect the headlight cleaner hose.

      Note

      Prepare a drain pan or a piece of cloth in case washer fluid leaks.

    9. Disconnect the 2 fog light connectors and remove the front bumper assembly.

  8. REMOVE HEADLIGHT ASSEMBLY LH


    1. A016217

      Disconnect the connector as shown in the illustration.

    2. A0160SR

      Remove the 3 bolts.

    3. Disengage the headlight bracket pin and remove the headlight assembly.

  9. REMOVE NO. 3 COOL AIR INTAKE DUCT SUB-ASSEMBLY


    1. A0163D1

      Remove the 3 front fender liner LH screws.

    2. A0162S5

      Disengage the engine under cover clip.

    3. A0160HW

      Remove the 2 bolts, the screw, and the No. 3 air intake duct sub-assembly.

  10. DRAIN WASHER FLUID


    1. A015YR0

      Remove the washer hose from the windshield washer motor and pump assembly, and drain the washer fluid.

  11. REMOVE WINDSHIELD WASHER JAR AND PUMP ASSEMBLY


    1. Disconnect each connector.

    2. A015YS1

      Remove the bolt.

    3. Pull the upper part of the washer jar and pump upward to remove it from the windshield washer jar and pump assembly.

    4. A015Z7I

      Remove the 3 bolts and the windshield washer jar and pump assembly.

  12. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY


    1. A015YHG

      Remove the windshield washer motor and pump assembly.