FRONT WIPER MOTOR INSTALLATION


  1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A0162CH

      Using a "TORX" socket wrench (T30), install the windshield wiper motor assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
    2. A0160TY

      Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.

    3. Install the windshield wiper link rod No. 1 to the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.

    4. A016094

      Apply MP grease to the pivot of the windshield wiper link assembly.

    5. Install the windshield wiper link rod No. 1 to the pivot of the windshield wiper link assembly as shown in the illustration.

    6. A0161ST

      Install the windshield wiper link rod No. 2 to the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.

  2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A0161NE

      Install the windshield wiper motor and link assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. Connect the connector.

  3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Engage the 11 claws.

      A015ZI2
    2. A015ZRH

      Install the cowl top ventilator louver sub-assembly with the 2 clips.

  4. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A0161WUE01

      Clean the wiper arm serrations.

    3. Clean the wiper pivot serrations with a wire brush (when reinstalling).

    4. A0160ONE01

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand to fasten the nut.

      Area Measurement
      A 15 to 30 mm (0.591 to 1.18 in.)
      B Approx. 40 mm (1.57 in.)
  5. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A0161WUE01

      Clean the wiper arm serrations.

    3. Clean the wiper pivot serrations with a wire brush (when reinstalling).

    4. A0162P6E01

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand to fasten the nut.

      Area Measurement
      A 16 to 31 mm (0.630 to 1.22 in.)
      B Approx. 20 mm (0.787 in.)
    5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

  6. INSTALL FRONT WIPER ARM HEAD CAP


    1. A015YS0

      Install the front wiper arm head cap.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  7. INSTALL ROOF DRIP SIDE FINISH MOULDING LH


    1. Engage the 2 clips and install the center roof drip side finish moulding.

      A0163FV
  8. INSTALL ROOF DRIP SIDE FINISH MOULDING RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  9. INSTALL FRONT UPPER FENDER PROTECTOR LH


    1. A0162I4

      Engage the claw and the 4 clips and install the front upper fender protector LH.

    2. Engage the clip on the rubber portion of the cowl top ventilator louver sub-assembly with the front upper fender protector LH.

  10. INSTALL FRONT UPPER FENDER PROTECTOR RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  11. INSTALL ENGINE ROOM SIDE COVER LH (for LHD)


    1. A016120

      Install the engine room side cover LH with the 5 clips.

  12. INSTALL ENGINE ROOM SIDE COVER LH (for RHD)


    1. A015Z63

      Install the engine room side cover LH with the 4 clips.

  13. INSTALL ENGINE ROOM SIDE COVER RH (for LHD)


    1. A0161AL

      Install the engine room side cover RH with the 3 clips.

  14. INSTALL ENGINE ROOM SIDE COVER RH (for RHD)


    1. A015YK3

      Install the engine room side cover RH with the 4 clips.

  15. INSTALL COOL AIR INTAKE DUCT SEAL


    1. A01638L

      Install the cool air intake duct seal with the 9 clips.