FRONT WIPER MOTOR REMOVAL


  1. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01638L

      Using a clip remover, remove the 9 clips and cool air intake duct seal.

  2. REMOVE ENGINE ROOM SIDE COVER LH (for LHD)


    1. A016120

      Remove the 5 clips and engine room side cover LH.

  3. REMOVE ENGINE ROOM SIDE COVER LH (for RHD)


    1. A015Z63

      Remove the 4 clips and engine room side cover LH.

  4. REMOVE ENGINE ROOM SIDE COVER RH (for LHD)


    1. A0161AL

      Remove the 3 clips and engine room side cover RH.

  5. REMOVE ENGINE ROOM SIDE COVER RH (for RHD)


    1. A015YK3

      Remove the 4 clips and engine room side cover RH.

  6. REMOVE FRONT UPPER FENDER PROTECTOR LH


    1. A0162I4

      Separate the clip on the rubber portion of the cowl top ventilator louver sub-assembly from the front upper fender protector LH.

    2. Disengage the 4 clips and the claw to remove the front upper fender protector LH.

  7. REMOVE FRONT UPPER FENDER PROTECTOR RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  8. REMOVE ROOF DRIP SIDE FINISH MOULDING LH


    1. Put protective tape around the roof drip side finish moulding.

    2. Using a moulding remover, disengage the 6 clips and remove the roof drip side finish moulding.

      Note


      • Do not remove the clips.

      • If the clips are damaged or dropped off, replace them with new clips.

      A0163FVE01

  9. REMOVE ROOF DRIP SIDE FINISH MOULDING RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  10. REMOVE FRONT WIPER ARM HEAD CAP


    1. A015ZOKE01

      Using a screwdriver, remove the front wiper arm head cap.

      Tech Tips


      • Use the same procedure for the RH side and LH side.

      • Tape the screwdriver tip before use.

  11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A0160CI

      Remove the nut and the front wiper arm and blade assembly LH.

  12. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A01603Q

      Remove the nut and the front wiper arm and blade assembly RH.

  13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A015ZRH

      Remove the 2 clips.

    2. Disengage the 11 claws and pull out the cowl top ventilator louver sub-assembly.

      A015ZVQ

  14. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A0161NE

      Disconnect the connector.

    2. Remove the 2 bolts.

    3. A0161Q4

      Disengage the rubber pin of the windshield wiper motor from the vehicle body as shown in the illustration.

    4. Remove the windshield wiper motor and link assembly.

  15. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A016074E01

      Using a screwdriver, separate the windshield wiper No. 2 link rod from the crank arm pivot of the front wiper motor assembly as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A0163BVE01

      Using a screwdriver, separate the windshield wiper No. 1 link rod from the pivot of the front wiper link assembly as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A015YH7E01

      Position the windshield wiper No. 1 link rod as shown in the illustration. Using a screwdriver, remove the windshield wiper No. 1 link rod.

      Tech Tips

      Tape the screwdriver tip before use.

    4. A0162CH

      Using a "TORX" socket wrench (T30), remove the 2 bolts and the windshield wiper motor assembly from the windshield wiper link assembly.