POWER MIRROR CONTROL SYSTEM Power Mirror cannot be Adjusted with Power Mirror Switch

DESCRIPTION

• A switch signal of the outer mirror switch is transmitted to the selected outer mirror control ECU by way of the main body ECU RH. Then, the outer mirror control ECU activates the mirror motor to move the mirror UP, DOWN, RIGHT or LEFT in response to the input.

• Mirror control switch and memorized mirror position signals (from the front power seat switch (position control ECU)) are sent to the mirror control ECU. The mirror control ECU moves the selected mirror UP, DOWN, LEFT or RIGHT in response to the input.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC

   
   

   1. Check for multiplex communication system DTCs.

      Result
      Result Proceed to Multiplex communication system DTC is not output A Multiplex communication system DTC is output B

   
   

   B

   GO TO MULTIPLEX COMMUNICATION SYSTEM Click here

   A

2. INSPECT OUTER MIRROR SWITCH

   
   

   1. 

      Remove the outer mirror switch Click here.

   2. Measure the resistance according to the value(s) in the table below when the switch is operated.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition 2 - 3 Adjust switch: Off Select switch: L or R 10 kΩ or higher Adjust switch: Up Select switch: L or R 90 to 110 Ω Adjust switch: Down Select switch: L or R 437 to 503 Ω Adjust switch: Left Select switch: L or R 744 to 856 Ω Adjust switch: Right Select switch: L or R 225 to 275 Ω 1 - 2 Select switch: L 90 to 110 Ω Select switch: R 10 Ω or less Neutral 10 kΩ or higher 4 -7 6 - 8 Retract switch not pressed Below 1 Ω 4 - 8 6 - 7 Retract switch pressed Below 1 Ω

   
   

   NG

   REPLACE OUTER MIRROR SWITCH Click here

   OK

3. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU RH)

   
   

   1. for LHD

      
      

      1. Disconnect the M8 and J74 connectors.

         

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition M8-3 (M+) - J74-11 (MIRB) Always Below 1 Ω M8-1 (MSW) - J74-12 (MIRS) Always Below 1 Ω M8-2 (E) - J74-3 (MIRE) Always Below 1 Ω M8-3 (M+) - Body ground Always 10 kΩ or higher M8-1 (MSW) - Body ground Always 10 kΩ or higher M8-2 (E) - Body ground Always 10 kΩ or higher

   2. for RHD

      
      

      1. Disconnect the L15 and J74 connectors.

         

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition L15-3 (M+) - J74-11 (MIRB) Always Below 1 Ω L15-1 (MSW) - J74-12 (MIRS) Always Below 1 Ω L15-2 (E) - J74-3 (MIRE) Always Below 1 Ω L15-3 (M+) - Body ground Always 10 kΩ or higher L15-1 (MSW) - Body ground Always 10 kΩ or higher L15-2 (E) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU RH)

   OK

4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the engine switch on (IG).

   3. Enter the following menus: Body / Mirror L/Mirror R / Active Test.

   4. Perform an Active Test according to the display on the tester.

      Mirror L and Mirror R
      Tester Display Test Details Control Range Diagnostic Note Mirror Up/Down Mirror vertical operation Up/Down - Mirror Right/Left Mirror horizontal operation Right/Left -

   
   

   NG

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU Click here

5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY

   
   

   1. 

      for LH side

      
      

      1. Disconnect the h1 connector.

      2. Apply battery voltage and check the operation of the mirror face.

         Standard
         Measurement Condition Mirror Operation Battery positive (+) → h1-1 (MV) Battery negative (-) → h1-10 (M+) Turns upward (A) Battery positive (+) → h1-10 (M+) Battery negative (-) → h1-1 (MV) Turns downward (B) Battery positive (+) → h1-9 (MH) Battery negative (-) → h1-10 (M+) Turns left (C) Battery positive (+) → h1-10 (M+) Battery negative (-) → h1-9 (MH) Turns right (D)

   2. 

      for RH side

      
      

      1. Disconnect the g1 connector.

   3. Apply battery voltage and check the operation of the mirror face.

      Standard
      Measurement Condition Mirror Operation Battery positive (+) → g1-1 (MV) Battery negative (-) → g1-10 (M+) Turns upward (A) Battery positive (+) → g1-10 (M+) Battery negative (-) → g1-1 (MV) Turns downward (B) Battery positive (+) → g1-9 (MH) Battery negative (-) → g1-10 (M+) Turns left (C) Battery positive (+) → g1-10 (M+) Battery negative (-) → g1-9 (MH) Turns right (D)

   
   

   NG

   REPLACE OUTER REAR VIEW MIRROR ASSEMBLY Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU Click here