SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Sliding Roof / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Sliding Roof
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open SW SLIDE OPEN switch signal / ON or OFF

      ON: SLIDE OPEN switch pressed

      OFF: SLIDE OPEN switch not pressed

      		 -
      Close SW SLIDE CLOSE switch signal / ON or OFF

      ON: SLIDE CLOSE switch pressed

      OFF: SLIDE CLOSE switch not pressed

      		 -
      Up SW TILT UP switch signal / ON or OFF

      ON: TILT UP switch pressed

      OFF: TILT UP switch not pressed

      		 -
      Down SW TILT DOWN switch signal / ON or OFF

      ON: TILT DOWN switch pressed

      OFF: TILT DOWN switch not pressed

      		 -
      Hall IC1 Pulse Sliding roof operation signal/LO or HI

      LO: Sliding roof motor not operating

      HI: Sliding roof motor operating

      		 -
      Hall IC1 Status Sliding roof operation signal/NORMAL or LOCK

      NORMAL: Sliding roof motor operating

      LOCK: Sliding roof motor not operating

      		 -
      Hall IC2 Pulse Sliding roof operation signal/LO or HI

      LO: Sliding roof motor not operating

      HI: Sliding roof motor operating

      		 -
      Hall IC2 Status Sliding roof operation signal/NORMAL or LOCK

      NORMAL: Sliding roof motor operating

      LOCK: Sliding roof motor not operating

      		 -
      Ignition (Direct Signal) Engine switch signal/ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Ignition (MPX) Engine switch signal (MPX signal)/ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Door Courtesy Driver's door courtesy light switch signal/ON or OFF

      ON: Driver's door open

      OFF: Driver's door closed

      		 -
      Door Key Open Operation Key-linked sliding roof open signal/ON or OFF

      ON: Door lock turned to open position using key

      OFF: Door lock not turned

      		 -
      Door Key Close Operation Key-linked sliding roof close signal/ON or OFF

      ON: Door lock turned to close position using key

      OFF: Door lock not turned

      		 -
      Wireless Open Operation Wireless sliding roof open signal/ON or OFF

      ON: Transmitter UNLOCK switch pressed

      OFF: Transmitter UNLOCK switch not pressed

      		 -
      Wireless Close Operation Wireless sliding roof close signal/ON or OFF

      ON: Transmitter LOCK switch pressed

      OFF: Transmitter LOCK switch not pressed

      		 -
      Door Key Related (Open) Key-linked sliding roof open permit signal/Available or Not available

      Available: Turn and hold the driver side door key to UNLOCK position for 3 seconds or more

      Not Available: Any status except "Available" status

      		 -
      Door Key Related (Close) Key-linked sliding roof close permit signal/Available or Not available

      Available: Turn and hold the driver side door key to LOCK position for 3 seconds or more

      Not Available: Any status except "Available" status

      		 -
      Wireless Key Rel (Open) Wireless sliding roof open permit signal/Available or Not available

      Available: Press and hold the transmitter UNLOCK switch for 4 seconds or more with key not in the vehicle

      Not Available: Any status except "Available" status

      		 -
      Wireless Key Rel (Close) Wireless sliding roof close permit signal/Available or Not available

      Available: Press and hold the transmitter LOCK switch for 4 seconds or more with key not in the vehicle

      Not Available: Any status except "Available" status

      		 -
      Door Key Related Operation Key-linked sliding roof operation signal/Tilt or Slide

      Tilt: Sliding roof tilts

      Slide: Sliding roof slides

      		 -
      Wireless Key Rel Operation Wireless sliding roof operation signal/Tilt or Slide

      Tilt: Sliding roof tilts

      Slide: Sliding roof slides

      		 -
      Key Off Permission Key-off sliding roof operation permit signal/ON or OFF

      ON: Front doors are not opened within 45 seconds after engine switch turned off

      OFF: Any status except "ON" status

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Sliding Roof / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof CLOS/UP / OFF -
      Slide Roof Operate sliding roof OPN/DWN / OFF -