POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR

    Note

    The regulator arm must be below the intermediate position when installing the power window regulator motor.


    1. A0160B7

      Using a "TORX" socket wrench (T25), install the rear power window regulator motor with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new rear window regulator uses self-tapping screws to thread new installation holes when inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. Apply MP grease to the sliding parts on the rear door window regulator sub-assembly.

    2. A0160I5E03

      Install the temporary bolt to the rear door window regulator sub-assembly.

    3. Temporarily install the window regulator.

    4. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

    5. Connect the connector.

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A015ZU9

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter weatherstrip.

    2. A0161FP

      Install the rear door quarter window glass together with the rear door quarter window glass weatherstrip in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A0162MB

      Insert the rear door window division bar from above and install it with the 2 bolts and screw.

  6. INSTALL REAR DOOR GLASS RUN


    1. A0162X4

      Install the rear door glass run.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A0163AKE01

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Engage each clamp.

    5. Connect the connector.

  8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A0161ZA

      Engage the 3 claws to install the rear door inner glass weatherstrip.

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install the 2 rear door trim board retainers (green).

    2. A016170

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear inside handle.

    3. Connect each connector.

    4. A0162P8

      Engage the rear door trim board with the 3 clips of the rear door inner glass weatherstrip.

    5. A015ZS2

      Engage the 8 clips to install the rear door trim board to the rear door panel.

    6. Install the 2 screws.

  10. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A015Z2B

      Engage the 2 claws and 2 clips, and install the rear power window regulator switch assembly with rear door armrest base panel.

  11. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A0162FH

      Engage the 3 claws to install the rear door inside handle bezel plug.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here