POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A015ZZC

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.

  3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A015ZOD

      Using a moulding remover, disengage the 2 claws and 2 clips.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A015ZS2

      Remove the 2 screws.

    2. Using a clip remover, disengage the 8 clips.

    3. A015YK2E02

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. Remove the reference boss from the rear door panel.

    5. Raise the rear door trim board to disengage the 3 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

    6. A0162J7

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    7. Disconnect each connector and remove the rear door trim board sub-assembly.

    8. Remove the 2 rear door trim board retainers (green) from the rear door trim board.

  5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A015ZZL

      Using a moulding remover, disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.

  6. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A015YVA

      Disconnect the connector.

    2. Disengage each clamp.

    3. Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  7. REMOVE REAR DOOR GLASS RUN


    1. A0162X4

      Remove the rear door glass run.

  8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A0162MB

      Remove the 2 bolts, the screw, and the rear door window division bar sub-assembly.

  9. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01613S

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  10. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A015Z3E

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  11. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A0160I5E01

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.

    5. Remove the temporary bolt from the rear door window regulator.

  12. REMOVE REAR POWER WINDOW REGULATOR MOTOR


    1. A0160B7

      Using a "TORX" socket wrench (T25), remove the 3 screws and the rear power window regulator motor.