POWER WINDOW CONTROL SYSTEM Rear Power Window LH does not Operate with Rear Power Window Switch LH

DESCRIPTION

When the engine is running or the engine switch is on (IG) and window lock switch is OFF, the rear power window regulator motor assembly (for rear LH side) is operated by the multiplex network switch assembly (for rear LH side). The rear power window regulator motor assembly (for rear LH side) has motor, regulator, and sensor functions.

WIRING DIAGRAM

A0160EGE06

INSPECTION PROCEDURE

Note


  • When the rear power window regulator motor assembly (for rear LH side) connector, the multiplex network master switch assembly connector or the multiplex network switch assembly (for rear LH side) connector is disconnected, the power window control system must be initialized Click here.

  • Since the power window control system has functions that use multiplex communication, first confirm that there is no malfunction in the multiplex communication system by inspecting the multiplex communication functions in accordance with the How to Proceed with Troubleshooting procedures Click here. Then, conduct the following inspection procedure.

PROCEDURE


  1. CHECK FUSE (RR DOOR LH)


    1. Remove the RR DOOR LH fuse from the main body ECU LH (cowl side junction block LH).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      RR DOOR LH fuse Always Below 1 Ω

    NG

    REPLACE FUSE

    OK

  2. CHECK POWER WINDOW CONTROL SYSTEM (Rear LH Side Remote Up/Down Function)


    1. Check that the rear LH side remote up/down function operates normally Click here.

      OK
      Rear LH side remote up/down function operates normally.

    NG

    CHECK HARNESS AND CONNECTOR (SWITCH (for Rear LH Side) - BODY GROUND AND BATTERY) Click here

    OK

    REPLACE MULTIPLEX NETWORK SWITCH ASSEMBLY (for Rear LH side) Click here

  3. CHECK HARNESS AND CONNECTOR (SWITCH (for Rear LH Side) - BODY GROUND AND BATTERY)


    1. A016182E02

      Disconnect the multiplex network switch assembly (for rear LH side) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O1-7 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O1-12 (BDR) - O1-7 (GND) Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH OPERATION SIGNAL)


    1. Turn the engine switch on (IG).

    2. A0163E3E02

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      M7-6 (PWS) - Body ground Power window lock switch UNLOCK 11 to 14 V
      M7-6 (PWS) - Body ground Power window lock switch LOCK Below 1 V
      for RHD
      Tester Connection Condition Specified Condition
      L17-6 (PWS) - Body ground Power window lock switch UNLOCK 11 to 14 V
      L17-6 (PWS) - Body ground Power window lock switch LOCK Below 1 V

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (for Rear LH Side))


    1. A0161BQE06

      Disconnect the multiplex network master switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      M7-6 (PWS) - O1-11 (PCT1) Always Below 1 Ω
      M7-6 (PWS) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      L17-6 (PWS) - O1-11 (PCT1) Always Below 1 Ω
      L17-6 (PWS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH side)


    1. A015YSXE06

      Remove the rear power window regulator motor assembly (for rear LH side) Click here.

    2. Check power window regulator motor operation:


      1. Apply battery voltage to connector terminals 1 and 2.

        Note

        Do not apply battery voltage to any terminals except terminals 1 and 2.

      2. Check that the motor gear rotates smoothly as follows.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 1

        Battery negative (-) → 2

        		 Motor gear rotates clockwise

        Battery positive (+) → 2

        Battery negative (-) → 1

        		 Motor gear rotates counterclockwise

    3. Check PTC operation:

      Note

      This check must be performed with the power window regulator and door glass installed on the vehicle.


      1. Install the power window regulator motor Click here.

      2. Connect an electrical tester DC 400 A probe to the wire harness of terminal 1.

        A0161O3E34

        Note

        Match the arrow mark of the probe with the direction of the current flow.

      3. Fully close the door glass by pulling up the multiplex network switch assembly (for rear LH side). Wait for approximately 60 seconds.

      4. Continue to pull up the multiplex network switch assembly (for rear LH side) and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (current shut-off inspection).

        Standard
        4 to 90 seconds

      5. Wait for 60 seconds after the previous step, and then push down the multiplex network switch assembly (for rear LH side).

        OK
        The rear LH side window goes down.

    NG

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (SWITCH (for Rear LH Side) - REGULATOR MOTOR)


    1. Disconnect the front power window regulator motor assembly (for rear LH side) connector.

    2. A0161XIE10

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O1-6 (UP) - O7-1 (U) Always Below 1 Ω
      O1-1 (DN) - O7-2 (D) Always Below 1 Ω
      O1-6 (UP) - Body ground Always 10 kΩ or higher
      O1-1 (DN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MULTIPLEX NETWORK SWITCH ASSEMBLY (for Rear LH side) Click here