FRONT PASSENGER SEAT BELT WARNING LIGHT REMOVAL

Note

When disassembling the clock assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.


  1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A0161BO

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  2. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A016226

      Using a moulding remover, disengage the claw.

    2. A0161ZW

      Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  3. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A015YLQ

      Using a moulding remover, disengage the claw.

    2. A0160CR

      Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  4. REMOVE CONSOLE PANEL SUB-ASSEMBLY


    1. A0160RU

      Hold the front of the console panel sub-assembly as shown in the illustration and disengage the 8 clips by pulling the console panel sub-assembly in the direction shown by the arrow.

      Note

      Do not use any tools to disengage the clips. The use of tools may result in damage to the console panel sub-assembly.

    2. Disconnect the connectors and remove the console panel sub-assembly.

  5. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. A0160IR

      Remove the 2 screws <E>.

    2. A0160OX

      Pull the front ash receptacle assembly in the direction indicated by the arrow to disconnect the connectors and remove it.

  6. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A0163DOE02

      Using a screwdriver, disengage the 4 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A015ZH6E03

      Apply protective tape to the areas shown in the illustration.

    3. A015ZAL

      Using a moulding remover, disengage the 4 claws starting from the right of the No. 3 instrument panel register assembly. Disengage the remaining 3 claws by pulling the No. 3 instrument panel register assembly by hand.

      Note

      Do not pry the lower part of the No. 3 instrument panel register assembly. Doing so may damage the assembly.

    4. Disconnect the connectors.

  7. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A0160YT

      Disengage the 4 claws and remove the center lower instrument cluster finish panel.

  8. REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System)


    1. A015ZQC

      Remove the 4 bolts.

    2. Pull the integration control panel with radio receiver assembly toward the rear of the vehicle.

    3. Disconnect each connector and remove the panel.

  9. REMOVE NO. 1 RADIO BRACKET (w/o Navigation System)


    1. A0160RO

      Remove the 6 bolts and No. 1 radio bracket.

  10. REMOVE NO. 2 RADIO BRACKET (w/o Navigation System)


    1. A0161EW

      Remove the 6 bolts and No. 2 radio bracket.

  11. REMOVE RADIO RECEIVER ASSEMBLY (w/o Navigation System)


    1. A0162XO

      Slide the integration control panel in the direction shown by the arrow to remove the radio receiver assembly.

  12. REMOVE CLOCK ASSEMBLY (w/o Navigation System)


    1. A0162OB

      Remove the 6 screws.

    2. A0162I6

      Disengage the 5 claws and panel.

    3. A0162KSE01

      Remove the 9 screws and cover.

    4. A0161JJ

      Disconnect the connectors.

    5. Remove the clock assembly.

  13. REMOVE MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System)


    1. A0162FS

      Remove the 4 bolts.

    2. Pull the multi-display with radio receiver assembly toward the rear of the vehicle.

    3. Disconnect each connector and remove the multi-display.

  14. REMOVE NO. 1 RADIO BRACKET (w/ Navigation System)


    1. A015YV5

      Disengage the connector clamp.

    2. A0160LX

      Remove the 7 bolts and No. 1 radio bracket.

  15. REMOVE NO. 2 RADIO BRACKET (w/ Navigation System)


    1. A015Z6H

      Remove the 7 bolts and No. 2 radio bracket.

  16. REMOVE RADIO RECEIVER ASSEMBLY (w/ Navigation System)


    1. A0160AI

      Slide the multi-display in the direction shown by the arrow to remove the radio receiver assembly.

  17. REMOVE CLOCK ASSEMBLY (w/ Navigation System)


    1. A01622NE02

      Apply protective tape to the places shown in the illustration.

    2. A0161VO

      Insert 2 precision screwdrivers (φ1.5 or less) into the holes on both sides of the clock assembly at the angle as shown in the illustration.

      Note

      Do not pry on the clock assembly with the screwdrivers as it may damage the clock assembly.

      Tech Tips

      If precision screwdrivers are not available, use in-vehicle tools (part No. 09135-53010).

    3. A015Z04E01

      Insert a screwdriver with its tip taped from the underside of the hazard switch, and pull and remove the clock assembly.

      Note

      Do not pry on the hazard switch with the screwdriver as it may damage the switch.