FRONT SEAT CUSHION HEATER INSTALLATION


  1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 16 new hog rings.

      A01612KE01

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  2. INSTALL FRONT SEAT CUSHION COVER WITH PAD


    1. A0163E4

      Engage the hooks.

    2. Install the front seat cushion cover with pad with the 2 clips.

    3. for Driver Side:


      1. A01607R

        Engage the 3 clamps.

      2. Connect the 2 connectors.

    4. for Passenger Side:


      1. A01634I

        Engage the 4 clamps.

      2. Connect the 2 connectors.

      3. A01615N

        Engage the 2 clamps and connect the occupant detection sensor connector.

  3. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. Connect the connector to the lumbar switch.

    2. A0161TM

      Engage the claw.

    3. Install the front seat cushion shield assembly with the 6 screws.

    4. A015ZYM

      Engage the 2 hooks and install the 2 rubber bands of the front seatback board to the seat frame.

  4. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A0161JR

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  5. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A0160MN

      Engage the 2 claws and install the reclining power seat switch knob.

  6. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A0162K4E02

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. A0160LBE01

      for Driver Seat:


      1. Connect the connector and engage the 3 clamps.

    3. for Passenger Seat:


      1. Connect the connector and engage the 4 clamps.

  7. INSTALL FRONT SEAT ASSEMBLY


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the power seat switch knob and move the seat to the rearmost position.

    6. A0161EEE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    7. Operate the power seat switch knob and move the seat to the foremost position.

    8. A0162WME01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  8. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. A015ZKS

      Engage the 2 claws and install the rear inner seat track bracket cover.

  9. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. A0160NB

      Engage the 2 claws and install the rear outer seat track bracket cover.

  10. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A015Z4U

      Engage the 2 claws and install the front inner seat track bracket cover.

  11. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. A0163FR

      Engage the 2 claws and install the front outer seat track bracket cover.

  12. INSTALL FRONT SEAT HEADREST ASSEMBLY

  13. INSPECT SRS WARNING LIGHT

    Tech Tips

    Inspect the SRS warning light Click here.

  14. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation.

    2. Check the seat heater operation.


      1. Turn the engine switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.