FRONT SEAT CUSHION HEATER REMOVAL


  1. REMOVE FRONT SEAT HEADREST ASSEMBLY

  2. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A0163FR

      Disengage the 2 claws and remove the front outer seat track bracket cover.

  3. REMOVE FRONT INNER SEAT TRACK BRACKET COVER


    1. A015Z4U

      Disengage the 2 claws and remove the front inner seat track bracket cover.

  4. REMOVE REAR OUTER SEAT TRACK BRACKET COVER


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A0160NB

      Disengage the 2 claws and remove the rear outer seat track bracket cover.

  5. REMOVE REAR INNER SEAT TRACK BRACKET COVER


    1. A015ZKS

      Disengage the 2 claws and remove the rear inner seat track bracket cover.

  6. REMOVE FRONT SEAT ASSEMBLY


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A0162WM

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the power seat switch knob and move the seat to the rearmost position.

    4. A0161EE

      Remove the 2 bolts on the front side of the seat.

    5. Operate the power seat switch knob and move the seat to the center position. Also, operate the power seat switch knob and move the seatback to the upright position.

    6. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system Click here.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. Disconnect the connectors under the seat.

    8. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    1. A0160LBE01

      for Driver Seat:


      1. Disconnect the connector and disengage the 3 clamps.

    2. for Passenger Seat:


      1. Disconnect the connector and disengage the 4 clamps.

    3. A0161U1

      Remove the nut and front seat inner belt assembly.

  8. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A0160GGE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the reclining power seat switch knob.

  9. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A0162PJE01

      Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the slide and vertical power seat switch knob.

  10. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A015ZYM

      Disengage the 2 hooks and remove the 2 rubber bands of the front seatback board from the front seat frame.

    2. A0161TM

      Remove the 6 screws.

    3. Disengage the claw and remove the front seat cushion shield assembly.

    4. Disconnect the connector from the front power seat lumbar switch.

  11. REMOVE FRONT SEAT CUSHION COVER WITH PAD


    1. for Driver Side:


      1. A01607R

        Disconnect the 2 connectors.

      2. Disengage the 3 clamps.

    2. for Passenger Side:


      1. A01615N

        Disengage the 2 clamps and separate the occupant detection sensor connector.

      2. A01634I

        Disconnect the 2 connectors.

      3. Disengage the 4 clamps.

    3. A0163E4

      Using a clip remover, remove the 2 clips.

    4. Disengage the hooks and remove the front seat cushion cover with pad.

  12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. Remove the 16 hog rings and the separate type front seat cushion cover from the seat cushion pad.

      A01612KE01