ENTRY LOCK AND UNLOCK SWITCH REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A0161A6

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A015ZWU

      Using a moulding remover, disengage the 3 claws and the 2 clips.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01631K

      Using a moulding remover, disengage the 3 claws and 2 clips.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  5. REMOVE COURTESY LIGHT ASSEMBLY


    1. A015ZOI

      Using a moulding remover, disengage the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A0160MG

      Remove the 2 screws.

    2. Using a clip remover, disengage the 9 clips.

    3. A01604GE02

      Pull out the front door trim board in the direction indicated by the arrow.

    4. Remove the reference boss from the front door panel.

    5. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.

    6. A0160JT

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

    7. Disconnect each connector and remove the front door trim board sub-assembly.

    8. Remove the 2 front door trim board retainers (green) from the front door trim board.

  7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A0160NK

      Using a moulding remover, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.

  8. REMOVE FRONT DOOR TRIM COVER


    1. A016263

      Remove the screw.

    2. Using a clip remover, disengage the 6 clips and remove the front door trim cover.

  9. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A015YH3

      Disconnect each connector.

    2. Disengage each clamp and remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  10. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    1. A0160NJ

      Using an emergency key, disengage the 2 claws and remove the front door outside handle cover.

  11. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A016229

      Remove the hole plug.

    2. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door lock cylinder.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A0163AF

      Remove the hole plug.

    2. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  13. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A015YWV

      Disconnect the connector.

    2. Using a "TORX" socket wrench (T30), loosen the screw.

    3. A0163AD

      Remove the front door outside handle assembly as shown in the illustration.