ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Unlock Function does not Operate

DESCRIPTION

If the front passenger door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. Any of the following components may have a malfunction: 1) touch sensor circuit certification ECU (smart key ECU assembly); 2) front door outside handle assembly (front passenger side); or 3) door electrical key oscillator (front passenger side).

WIRING DIAGRAM

A015ZASE14

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock Click here.

      OK
      Locked doors unlock.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Body (Main Body ECU RH (Cowl Side Junction Block RH))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Passenger Lock Pos SW Front passenger side door lock position switch signal/ON or OFF

      ON: Front passenger side door is unlocked

      OFF: Front passenger side door is locked

      		 -
      OK
      On the intelligent tester screen, ON or OFF will be displayed accordingly.
      Result
      Result Proceed to
      OK A
      NG

      B

      (Refer to "Front Passenger Door LOCK/UNLOCK Functions do not Operate" in the problem symptoms table)

    B

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) Click here

    A

  3. READ VALUE USING INTELLIGENT TESTER (DOOR OUTSIDE HANDLE)


    1. Enter the following menus: Body / Entry & Start / Data List.

    2. Read the Data List according to the display on the intelligent tester.

      Entry & Start (Certification ECU (Smart Key ECU Assembly))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Touch Sensor Status of touch sensor (front passenger side) / ON or OFF

      ON: Touch sensor is touched

      OFF: Touch sensor is not touched

      		 -
      OK
      On the intelligent tester screen, the display changes between ON and OFF according to the chart above.

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)


    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. A015YHME14

      Disconnect the door electrical key oscillator (front passenger side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      P33-6 (SEL2) - n2-4 (SEL) Always Below 1 Ω
      P33-23 (SEN2) - n2-6 (SENS) Always Below 1 Ω
      P33-6 (SEL2) - Body ground Always 10 kΩ or higher
      P33-23 (SEN2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      P33-6 (SEL1) - o2-4 (SEL) Always Below 1 Ω
      P33-23 (SEN1) - o2-6 (SENS) Always Below 1 Ω
      P33-6 (SEL1) - Body ground Always 10 kΩ or higher
      P33-23 (SEN1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)


    1. A015Z5PE70

      Disconnect the front door outside handle assembly (front passenger side) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      n1-6 (SGT) - n2-2 (SGT) Always Below 1 Ω
      n1-6 (SGT) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      o1-6 (SGT) - o2-2 (SGT) Always Below 1 Ω
      o1-6 (SGT) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side)


    1. Replace the door electrical key oscillator (front passenger side) Click here.


    NEXT

  7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Front Passenger Side)


    1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) Click here

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

  8. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)


    1. Replace the front door outside handle assembly (front passenger side) Click here.


    NEXT

  9. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)


    1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)