ENTRY AND START SYSTEM (for Entry Function) All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate

DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, the communication line between the door control receiver and certification ECU (smart key ECU assembly) is normal. When the entry functions do not operate, one of the following may be the cause: 1) entry cancel function is set through customization; 2) malfunction in entry and start system communication line (electrical key transmitter and vehicle); or 3) wave interference.

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (ENTRY CANCEL FUNCTION)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Entry & Start (Certification ECU (Smart Key ECU Assembly))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Entry Cancel SW Entry door lock function cancel / ON or OFF Mode status displayed -
      Result
      Result Proceed to
      Entry function is ON A
      Entry function is OFF B

    A

    PERFORM CANCELLATION OF ENTRY KEY CANCEL FUNCTION Click here

    B

  2. CHECK WAVE ENVIRONMENT


    1. Move the electrical key transmitter as described below and perform the operation inspection.

      Tech Tips


      • When the electrical key transmitter is brought near the door outside handle assembly or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • The transmitting waves of the wireless functions and entry functions are the same, but the wave logic is different. Therefore, it is possible that only the wireless functions or only the entry functions are affected by wave interference.

    2. A0160MPE02

      Bring the electrical key transmitter near the driver door outside handle assembly, and perform a front driver door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

    3. A0162QLE01

      Bring the electrical key transmitter near the front passenger door outside handle assembly, and perform a front passenger door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

    4. A015ZH1E02

      Bring the electrical key transmitter near the outside electrical key oscillator (luggage compartment), and perform an entry luggage compartment door open function check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.

      Tech Tips

      If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Result Proceed to
      Some operation checks are normal A
      All operation checks fail B

    A

    AFFECTED BY WAVE INTERFERENCE

    B

  3. PERFORM KEY DIAGNOSTIC MODE INSPECTION


    1. A0160MPE01

      Diagnostic mode inspection (door electrical key oscillator (driver side))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Driver Side.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    2. A0162QLE02

      Diagnostic mode inspection (door electrical key oscillator (front passenger side))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    3. A0160PAE01

      Diagnostic mode inspection (indoor electrical key oscillator (front floor))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Front Room.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    4. A0160VNE01

      Diagnostic mode inspection (indoor electrical key oscillator (rear floor))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Rear Room.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

    5. A0162T7E01

      Diagnostic mode inspection (indoor electrical key oscillator (luggage compartment))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Luggage (inside)

      5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

    6. A015ZH1E01

      Diagnostic mode inspection (outside electrical key oscillator (luggage compartment))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Luggage (outside).

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

        Result
        Result Proceed to
        Some diagnostic mode inspections fail (door) A
        Some diagnostic mode inspections fail (interior) B
        Some diagnostic mode inspections fail (luggage compartment) C
        All diagnostic mode inspections are normal D
        All diagnostic mode inspections fail E

    A

    GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table Flowchart for Each Door) Click here

    B

    GO TO OTHER PROBLEM (Proceed to Room Oscillator does not Recognize Key) Click here

    C

    GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) Click here

    D

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    E

  4. REPLACE ELECTRICAL KEY TRANSMITTER


    1. Replace the electrical key transmitter.


    NEXT

  5. REGISTER ELECTRICAL KEY TRANSMITTER


    1. Register the electrical key transmitter.


    NEXT

  6. CHECK ELECTRICAL KEY TRANSMITTER (OPERATION)


    1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (ELECTRICAL KEY TRANSMITTER IS DEFECTIVE)