ENTRY AND START SYSTEM (for Entry Function) CUSTOMIZE PARAMETERS


  1. CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

    Tech Tips

    The items in the table below can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.

    Tech Tips

    The following functions default settings are ON. Parts of these functions can be customized.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Utility / Customize Setting.

    5. Select the setting by referring to the table below.

      Entry & Start
      Tester Display Default Content Setting
      Ignition Available Area ALL Function that switches the entry ignition detection area. FRONT or ALL
      Park Wait Time 2.5 s Function that sets waiting time to permit opening the door after the door is locked with the entry lock function. 0.5 s, 1.5 s, 2.5 s or 5 s
      Trunk Open Mode ON Function that permits opening the luggage compartment door. ON or OFF
      Key Low Battery Warning ON Function that warns the driver that the key battery is low. ON or OFF

  2. ENTRY UNLOCK MODE SWITCHING

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.


    1. To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously press and hold the key LOCK switch and another key switch for 5 seconds.

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

      Note

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.


      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When any touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the entry door control receiver and changes the entry and start system to the entry unlock mode.

    3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been changed.


      1. w/o Panic Switch:

        A015YYHE06

        Tech Tips


        • This procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

        • The above illustration is for LHD vehicles. For RHD vehicles, the left side and right side are reversed.

      2. w/ Panic Switch:

        A015Z9TE01

        Tech Tips

        This procedure only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

  3. KEY CANCEL

    Note

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.

    The key cancel operation disables the following functions:


    • Entry Unlock/Lock

    • Entry Luggage Compartment Open

    • Key Lock-in Prevention

    • Warning

    • Memory Call


    1. The operation procedure is as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked


      1. Press the UNLOCK switch of the key once.

      2. Open the driver door within 5 seconds.

      3. Press the UNLOCK switch of the key twice within 5 seconds.

      4. Repeat open → close twice for the driver door within 30 seconds, and open again.

        (Driver door: Open → Close → Open → Close → Open)

      5. Press the UNLOCK switch of the key twice within 5 seconds.

      6. Repeat open → close once for the driver door within 30 seconds, and open again.

        (Driver door: Open → Close → Open)

      7. Close the driver door within 5 seconds.

        When key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.