DOOR CONTROL RECEIVER (for Rear Side) INSTALLATION


  1. INSTALL DOOR CONTROL RECEIVER


    1. Install the door control receiver with the bolt.

    2. A016327

      Connect the connector.

  2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A015YRT

      Pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Engage the 3 clips and 5 claws to install the package tray trim panel assembly.

    3. A01630U

      Engage the 4 claws to install the rear seat shoulder belt cover LH.

      Tech Tips

      Use the same procedures for the RH side and the LH side.

    4. A0160XQE01

      Install the floor end of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap protruding parts of the floor panel.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

    5. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  3. INSTALL CENTER STOP LIGHT SET


    1. Connect the connector.

    2. A0163GQ

      Engage the 2 guides.

    3. Engage the 2 claws and install the center stop light set.

  4. INSTALL ROOF SIDE INNER GARNISH LH


    1. A01626A

      Engage the claw and 4 clips, and install the roof side garnish inner LH.

  5. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  6. INSTALL REAR SEAT SIDE GARNISH LH


    1. A0163A2

      Engage the 5 claws and install the rear seat side garnish LH.

  7. INSTALL REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  8. INSTALL REAR DOOR SCUFF PLATE LH


    1. A016266

      Engage the 2 clips.

    2. A015YIJ

      Engage the 5 claws and install the rear door scuff plate LH.

  9. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  10. INSTALL REAR SEATBACK ASSEMBLY


    1. Place the seatback in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A0163EJ

      Engage the 3 hooks.

    3. Install the rear seatback assembly with the 4 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. A015YIY

      Pass the seat belt through the rear seat shoulder belt guide RH.

    5. Engage the 2 claws and close the 2 caps of the rear seat shoulder belt guide RH.

    6. A0160LI

      Pass the seat belt through the rear seat shoulder belt guide LH.

    7. Engage the 2 claws and close the 2 caps of the rear seat shoulder belt guide LH.

  11. INSTALL REAR SEAT HEADREST ASSEMBLY RH

  12. INSTALL REAR SEAT HEADREST ASSEMBLY LH

  13. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. A0162ZH

      Engage the 2 rear hooks of the seat cushion to the child restraint seat anchor bracket.

    2. Engage the 2 front hooks of the seat cushion to the vehicle body.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.