REAR DOOR LOCK INSTALLATION


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A015Z6E

      Install the rear door inside locking cable assembly.

    2. A015YH8

      Engage the 3 claws.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A0160H6

      Install the rear door lock remote control cable assembly.

    2. A015YSL

      Engage the claw.

  3. INSTALL REAR DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness sealing and/or using a damaged door lock wiring harness seal may cause water intrusion to the connection, and result in a malfunction in the rear door lock assembly.


    1. Apply MP grease to the sliding parts on the rear door lock assembly.

    2. Install a new door lock wiring harness seal to the rear door lock assembly.

    3. A0162YK

      Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    5. Using a "TORX" socket wrench (T30), install the rear door lock assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    6. Connect the connector.

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A015ZU9

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A0162MB

      Insert the rear door window division bar from above and install it with the 2 bolts and screw.

  6. INSTALL REAR DOOR GLASS RUN


    1. A0162X4

      Install the rear door glass run.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A0163AKE01

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Engage each clamp.

    5. Connect the connector.

  8. INSTALL REAR DOOR TRIM COVER


    1. A0160LL

      Engage the 5 clips to install the rear door trim cover.

    2. Install the screw.

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Install the 2 rear door trim board retainers (green).

    2. A016170

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear inside handle.

    3. Connect each connector.

    4. A0162P8

      Engage the rear door trim board with the 3 clips of the rear door inner glass weatherstrip.

    5. A015ZS2

      Engage the 8 clips to install the rear door trim board to the rear door panel.

    6. Install the 2 screws.

  10. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A015Z2B

      Engage the 2 claws and 2 clips, and install the rear power window regulator switch assembly with rear door armrest base panel.

  11. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A0162FH

      Engage the 3 claws to install the rear door inside handle bezel plug.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here