REAR VIEW MONITOR SYSTEM Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

The display signal from the rear television camera assembly transmits to the display and navigation module display.

WIRING DIAGRAM

A01636EE03

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - TELEVISION CAMERA)


    1. Disconnect the J124 connector from the display and navigation module display.

    2. Disconnect the Q43 connector from the television camera assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q43-2 (CV+) - J124-5 (V+) Always Below 1 Ω
      Q43-4 (CB+) - J124-6 (CA+) Always Below 1 Ω
      Q43-3 (CGND) - J124-17 (CGND) Always Below 1 Ω
      Q43-1 (CV-) - J124-16 (V-) Always Below 1 Ω
      Q43-2 (CV+) - Body ground Always 10 kΩ or higher
      Q43-4 (CB+) - Body ground Always 10 kΩ or higher
      Q43-3 (CGND) - Body ground Always 10 kΩ or higher
      Q43-1 (CV-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT DISPLAY AND NAVIGATION MODULE DISPLAY


    1. Reconnect the Q43 connector to the television camera assembly.

    2. A015Z4TE26
      Text in Illustration
      *1

      Component with harness connected

      (Display and Navigation Module Display)

      Reconnect the J124 connector to the display and navigation module display.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J124-16 (V-) - Body ground Always Below 1 Ω
      J124-17 (CGND) - Body ground Always Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J124-6 (CA+) - J124-17 (CGND)

      Engine switch on (IG)

      Shift lever in R

      		 5.5 to 7.0 V

    NG

    REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY Click here

    OK

  3. INSPECT REAR TELEVISION CAMERA ASSEMBLY


    1. A015Z4TE27

      Check that the J124 connector is connected to the display and navigation module display.

    2. A01608AE55

      Check that the J122 connector is connected to the display and navigation module display.

    3. A016195E02
      Text in Illustration
      *1

      Component with harness connected

      (Display and Navigation Module Display)
      *2 Waveform 1 (camera lens not covered, displaying an image)
      *3 Waveform 2 (camera lens covered, blacking out the screen)
      *4 Synchronization Signal
      *5 Video Waveform

      Check the waveform of the television camera assembly using an oscilloscope.

      OK
      Waveform is as shown in the illustration.
      Item Content
      Terminal No. (Symbol) J124-5 (V+) - J122-10 (GND1)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition Engine switch on (IG), shift lever in R

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.


    NG

    REPLACE TELEVISION CAMERA ASSEMBLY Click here

    OK

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Click here