AUDIO AND VISUAL SYSTEM (w/o Navigation System) Illumination Circuit

DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A015ZFFE02

INSPECTION PROCEDURE

Note

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except radio receiver assembly. B
      Illumination comes on for all components except integration control and panel assembly. C
      No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). D
      Illumination comes on only for steering pad switch assembly. E

    B

    CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (BATTERY - INTEGRATION CONTROL AND PANEL ASSEMBLY) Click here

    D

    GO TO LIGHTING SYSTEM Click here

    E

    GO TO METER / GAUGE SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)


    1. A0160JVE21
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Disconnect the spiral cable sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J24-12 (IL+2) - Body ground Light control switch tail or head 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the steering pad switch assembly connector.

    2. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

      A0162OCE01

    3. Check if the illumination for the steering pad switch assembly comes on.

      OK
      Illumination for the steering pad switch assembly comes on.
      Text in Illustration
      *A w/ Microphone *B w/o Microphone
      *1

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  4. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A0162YPE12
      Text in Illustration
      *1 Steering Pad Switch Assembly Side
      *2 Vehicle Side

      Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      k1-8 (EAU) - J24-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      k1-5 (IL+2) - J24-12 (IL+2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

      Note

      The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

      Tech Tips



    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR


    1. Disconnect the radio receiver assembly and spiral cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J108-6 (SWG) - J24-4 (EAU) Always Below 1 Ω
      J108-6 (SWG) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

  6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY)


    1. A015ZK7E48
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Disconnect the radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J107-2 (ILL+) - Body ground Light control switch tail or head 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the radio receiver assembly and combination meter assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J107-12 (ILL-) - J35-9 (ILL-) Always Below 1 Ω
      J35-9 (ILL-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

  8. CHECK HARNESS AND CONNECTOR (BATTERY - INTEGRATION CONTROL AND PANEL ASSEMBLY)


    1. A0160Z6E05
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Integration Control and Panel Assembly)

      Disconnect the integration control and panel assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J54-3 (ILL+) - Body ground Light control switch tail or head 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR


    1. Disconnect the integration control and panel assembly and the combination meter assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J54-10 (ILL-) - J35-9 (ILL-) Always Below 1 Ω
      J54-10 (ILL-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY Click here