AUDIO AND VISUAL SYSTEM (w/o Navigation System) Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as to when a switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM

A01605AE14

INSPECTION PROCEDURE

Note

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

PROCEDURE


  1. INSPECT RADIO RECEIVER ASSEMBLY


    1. A0160URE11
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Disconnect the radio receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J108-7 (SW1) - J108-6 (SWG) No switch pushed 95 to 105 kΩ
      J108-7 (SW1) - J108-6 (SWG) Seek+ switch pushed Below 2.5 Ω
      J108-7 (SW1) - J108-6 (SWG) Seek- switch pushed 312 to 345 Ω
      J108-7 (SW1) - J108-6 (SWG) Volume+ switch pushed 950 to 1050 Ω
      J108-7 (SW1) - J108-6 (SWG) Volume- switch pushed 2954 to 3265 Ω
      J108-8 (SW2) - J108-6 (SWG) No switch pushed 95 to 105 kΩ
      J108-8 (SW2) - J108-6 (SWG) MODE switch pushed Below 2.5 Ω
      J108-8 (SW2) - J108-6 (SWG)*1 Voice switch pushed 2954 to 3265 Ω
      J108-8 (SW2) - J108-6 (SWG)*1 On hook switch pushed 312 to 345 Ω
      J108-8 (SW2) - J108-6 (SWG)*1 Off hook switch pushed 950 to 1050 Ω

      • *1: w/ Microphone


    NG

    INSPECT STEERING PAD SWITCH ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the steering pad switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      A0163EWE01
      Standard Resistance
      Tester Connection Condition Specified Condition
      k1-10 (AU1) - k1-8 (EAU) No switch pushed 95 to 105 kΩ
      k1-10 (AU1) - k1-8 (EAU) Seek+ switch pushed Below 2.5 Ω
      k1-10 (AU1) - k1-8 (EAU) Seek- switch pushed 312 to 345 Ω
      k1-10 (AU1) - k1-8 (EAU) Volume+ switch pushed 950 to 1050 Ω
      k1-10 (AU1) - k1-8 (EAU) Volume- switch pushed 2954 to 3265 Ω
      k1-9 (AU2) - k1-8 (EAU) No switch pushed 95 to 105 kΩ
      k1-9 (AU2) - k1-8 (EAU) MODE switch pushed Below 2.5 Ω
      k1-9 (AU2) - k1-8 (EAU)*1 Voice switch pushed 2954 to 3265 Ω
      k1-9 (AU2) - k1-8 (EAU)*1 On hook switch pushed 312 to 345 Ω
      k1-9 (AU2) - k1-8 (EAU)*1 Off hook switch pushed 950 to 1050 Ω

      • *1: w/ Microphone

      Text in Illustration
      *A w/ Microphone *B w/o Microphone
      *1

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 *2 Volume-
      *3 Volume+ *4 Seek-
      *5 Seek+ *6 MODE
      *7 Off hook *8 On hook
      *9 Voice - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A0162YPE11
      Text in Illustration
      *1 Steering Pad Switch Assembly Side
      *2 Vehicle Side

      Disconnect the steering pad switch assembly and spiral cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      k1-8 (EAU) - J24-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      k1-10 (AU1) - J24-6 (AU1) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      k1-9 (AU2) - J24-5 (AU2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

      Note

      The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

      Tech Tips



    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER ASSEMBLY)