VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1415, C1416

DTC Code DTC Name
C1415 Rear Speed Sensor RH Output Malfunction
C1416 Rear Speed Sensor LH Output Malfunction

DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for the ABS control system. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Elements). The speed sensor rotor, which consists of 48 sets of N and S poles arranged in a circle, is integrated with the inner race of the hub bearing.

To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by the 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward waveform to the ECU.

A0162H7E07
DTC Code DTC Detection Condition Trouble Area

C1415

C1416

Any of the following is detected:


  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

  2. At a vehicle speed 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

  3. At a vehicle speed 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.

  • Rear speed sensor RH/LH

  • Speed sensor circuit

  • Speed sensor rotor RH/LH

  • Brake actuator assembly (Skid control ECU)

Tech Tips


  • DTC C1415 is for the rear speed sensor RH.

  • DTC C1416 is for the rear speed sensor LH.

WIRING DIAGRAM

Refer to DTCs C1403 and C1404 Click here.

INSPECTION PROCEDURE

Note

When replacing the brake actuator assembly, perform zero point calibration and store system information Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Speed Open RR speed sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      RL Speed Open RL speed sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      OK
      There are no momentary interruptions.

      Tech Tips

      Perform the above inspection before removing the sensor and connector.


    NG

    CHECK REAR SPEED SENSOR INSTALLATION Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)


    1. Turn the engine switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Start the engine.

    4. Select the Data List on the intelligent tester Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Wheel Speed RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)

      When vehicle is stopped: 0 km/h (0 mph)

      When vehicle is being driven at a constant speed: No major fluctuation

      		 Similar speed as indicated on speedometer
      RL Wheel Speed RL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)

      When vehicle is stopped: 0 km/h (0 mph)

      When vehicle is being driven at a constant speed: No major fluctuation

      		 Similar speed as indicated on speedometer

    5. Check the speed value output from the speed sensor displayed on the intelligent tester.

      Tech Tips

      Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart Click here.

      OK
      The speed value output from the speed sensor displayed on the intelligent tester is the similar speed as indicated on the speedometer.

    NG

    CHECK REAR SPEED SENSOR INSTALLATION Click here

    OK

  3. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Clear the DTCs Click here.

    3. Start the engine.

    4. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

    5. Check if the same DTC is recorded Click here.

      Result
      Result Proceed to
      DTCs (C1415 and C1416) are not output A
      DTCs (C1415 and/or C1416) are output B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  4. CHECK REAR SPEED SENSOR INSTALLATION


    1. A0162WXE05

      Check the speed sensor installation.

      OK
      There is no clearance between the sensor and the rear axle carrier.
      The installation bolt is tightened properly.
      Torque
      8.5 N*m (87 kgf*cm, 75 in.*lbf)

    NG

    INSTALL REAR SPEED SENSOR CORRECTLY Click here

    OK

  5. CHECK REAR SPEED SENSOR TIP


    1. Remove the rear speed sensor Click here.

    2. Check the speed sensor tip.

      OK
      No scratches, oil, or foreign matter on the sensor tip.

      Note

      Check the speed sensor signal after cleaning or replacement Click here.


    NG

    CLEAN OR REPLACE REAR SPEED SENSOR

    OK

  6. CHECK REAR SPEED SENSOR ROTOR


    1. Remove the rear speed sensor rotor Click here.

    2. Check the speed sensor rotor.

      OK
      No scratches, oil, or foreign matter on the rotors.

      Note

      Check the speed sensor signal after cleaning or replacement Click here.

      Tech Tips

      The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

      If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.


    NG

    CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)


    1. A015ZHOE05
      Text in Illustration
      *1 Skid Control Sensor Wire
      *2 Sensor Side Connector "A"
      *3 Vehicle Side Connector "B"
      *4 for RH
      *5 for LH

      Install the rear speed sensor and the rear speed sensor rotor.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the rear speed sensor connector and the skid control sensor wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      X1 ("A"-2) - X1 ("B"-4) Always Below 1 Ω
      X1 ("A"-2) - X1 ("B"-5) Always 10 kΩ or higher
      X1 ("A"-2) - Body ground Always 10 kΩ or higher
      X1 ("A"-1) - X1 ("B"-5) Always Below 1 Ω
      X1 ("A"-1) - X1 ("B"-4) Always 10 kΩ or higher
      X1 ("A"-1) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      Y1 ("A"-2) - Y1 ("B"-4) Always Below 1 Ω
      Y1 ("A"-2) - Y1 ("B"-5) Always 10 kΩ or higher
      Y1 ("A"-2) - Body ground Always 10 kΩ or higher
      Y1 ("A"-1) - Y1 ("B"-5) Always Below 1 Ω
      Y1 ("A"-1) - Y1 ("B"-4) Always 10 kΩ or higher
      Y1 ("A"-1) - Body ground Always 10 kΩ or higher

      Note

      Check the speed sensor signal after replacement Click here.


    NG

    REPLACE SKID CONTROL SENSOR WIRE

    OK

  8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)


    1. A015ZZOE06
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Skid Control ECU)
      *2

      Front view of wire harness connector

      (to Rear Speed Sensor)

      Reconnect the skid control sensor wire.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the skid control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A62-17 (RR+) - X1-2 (RR+) Always Below 1 Ω
      A62-17 (RR+) - Body ground Always 10 kΩ or higher
      A62-16 (RR-) - X1-1 (RR-) Always Below 1 Ω
      A62-16 (RR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A62-5 (RL+) - Y1-2 (RL+) Always Below 1 Ω
      A62-5 (RL+) - Body ground Always 10 kΩ or higher
      A62-4 (RL-) - Y1-1 (RL-) Always Below 1 Ω
      A62-4 (RL-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT SKID CONTROL ECU (SENSOR INPUT)


    1. A0162OHE11
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Rear Speed Sensor)

      Reconnect the skid control ECU connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Switch Condition Specified Condition
      X1-2 (RR+) - Body ground Engine switch on (IG) 8 to 14 V
      for LH
      Tester Connection Switch Condition Specified Condition
      Y1-2 (RL+) - Body ground Engine switch on (IG) 8 to 14 V

      Note

      Check the speed sensor signal after replacement Click here.

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step Click here.


    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    OK

    REPLACE REAR SPEED SENSOR Click here