VEHICLE STABILITY CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    7. According to the display on the intelligent tester, read the Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ABS Warning Light ABS warning light / ON or OFF

      ON: Warning light ON

      OFF: Warning light OFF

      		 -
      Brake Warning Light Brake warning light / ON or OFF

      ON: Warning light ON

      OFF: Warning light OFF

      		 -
      Buzzer Skid control buzzer / ON or OFF

      ON: Buzzer ON

      OFF: Buzzer OFF

      		 -
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Parking Brake SW Parking brake switch / ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      		 -
      Main Idle SW Main idle switch / ON or OFF

      ON: Accelerator pedal released

      OFF: Accelerator pedal depressed

      		 -
      Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF

      ON: Brake pedal depressed beyond the specified point

      OFF: Brake pedal not depressed beyond the specified point

      		 -
      Gear Position Gear position information / P/N, R, 1st-8th, FAIL, NOT R Actual gear position -
      Shift Lever Position Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL Actual shift lever position -
      Shift Information Shift information / ON or OFF ON: During gear change -
      Inspection Mode Inspection mode / OTHER or INSPECT

      OTHER: Normal mode

      INSPECT: Inspection mode

      		 -
      Number of IG ON (Inspection) Number of engine switch being turned on (IG) after entering inspection mode / min.: 0, max.: 255 - -
      Master Cylinder Sensor Master cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed
      Zero Point of M/C Memorized zero value / min.: -12.5 MPa, max.: 12.4 MPa - -
      Deceleration Sensor

      Acceleration sensor / min.: -18.52 m/s2, max.: 18.39 m/s2

      		- During deceleration/acceleration: Changes continuously
      Zero Point of Decele

      Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2

      		- -
      Deceleration Sensor2

      Acceleration sensor 2 / min.: -18.52 m/s2, max.: 18.39 m/s2

      		- During deceleration/acceleration: Changes continuously
      Zero Point of Decele2

      Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2

      		- -
      Yaw Rate Sensor Yaw rate sensor / min.: -128 deg/s, max.: 127 deg/s

      Vehicle stationary: 0 deg/s

      Right turn: -128 to 0 deg/s

      Left turn: 0 to 127 deg/s

      		 -
      Zero Point of Yaw Rate Memorized zero value / min.: -128 deg°/sec, max.: 127 deg°/sec - -
      Yaw Rate Sensor2 Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s

      Vehicle stationary: 0 deg/s

      Right turn: -128 to 0 deg/s

      Left turn: 0 to 127 deg/s

      		 -
      Zero Point of Yaw Rate2 Memorized zero value / min.: -128 deg°/sec, max.: 127 deg°/sec - -
      Steering Angle Sensor Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg

      Left turn: Increase

      Right turn: Decrease

      		 -
      Zero Point of Steering Angle Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg After steering angle sensor zero point calibration: 0 deg -
      Lateral G

      Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2

      		- During turning: Changes in proportion with acceleration
      Forward and Rearward G

      Forward and backward G / min.: -25.11 m/s2, max.: 24.91 m/s2

      		- During acceleration/deceleration: Changes in proportion with acceleration
      Yaw Rate Value Yaw rate value / min.: -128 deg/s, max.: 127 deg/s - During turning: Changes in proportion with yaw
      Steering Angle Value Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg - During steering operation: Changes in proportion with steering wheel rotation
      Stop Light Relay Stop light control relay / ON or OFF

      ON: Relay ON

      OFF: Relay OFF

      		 -
      Slip Indicator Light Slip indicator light / ON or OFF

      ON: Indicator light ON

      OFF: Indicator light OFF

      		 -
      FR Wheel Speed Front wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FL Wheel Speed Front wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      RR Wheel Speed Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      RL Wheel Speed Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      Vehicle Speed Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      FR Wheel Acceleration

      Front wheel RH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      FL Wheel Acceleration

      Front wheel LH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      RR Wheel Acceleration

      Rear wheel RH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      RL Wheel Acceleration

      Rear wheel LH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2

      		- During deceleration/acceleration: Changes continuously
      FR Wheel Direction Front wheel RH direction / FORWARD or BACK

      FORWARD: Forward

      BACK: Backward

      		 -
      FL Wheel Direction Front wheel LH direction / FORWARD or BACK

      FORWARD: Forward

      BACK: Backward

      		 -
      RR Wheel Direction Rear wheel RH direction / FORWARD or BACK

      FORWARD: Forward

      BACK: Backward

      		 -
      RL Wheel Direction Rear wheel LH direction / FORWARD or BACK

      FORWARD: Forward

      BACK: Backward

      		 -
      Stop Light Relay Output Stop light control relay output / ON or OFF

      ON: Relay output ON

      OFF: Relay output OFF

      		 -
      FR Wheel ABS Ctrl Status Front wheel RH ABS control status / ON or OFF ON: During control -
      FL Wheel ABS Ctrl Status Front wheel LH ABS control status / ON or OFF ON: During control -
      RR Wheel ABS Ctrl Status Rear wheel RH ABS control status / ON or OFF ON: During control -
      RL Wheel ABS Ctrl Status Rear wheel LH ABS control status / ON or OFF ON: During control -
      BA Ctrl Status BA control status / ON or OFF ON: During control -
      PBA Ctrl Status PBA control status / ON or OFF ON: During control -
      TRC (TRC) Ctrl Status TRC control status / ON or OFF ON: During control -
      TRC (TRC) Engine Ctrl Status TRC engine control status / ON or OFF ON: During control -
      TRC (TRC) Brake Ctrl Status TRC brake control status / ON or OFF ON: During control -
      FR Wheel VSC Ctrl Status Front wheel RH VSC control status / ON or OFF ON: During control -
      FL Wheel VSC Ctrl Status Front wheel LH VSC control status / ON or OFF ON: During control -
      RR Wheel VSC Ctrl Status Rear wheel RH VSC control status / ON or OFF ON: During control -
      RL Wheel VSC Ctrl Status Rear wheel LH VSC control status / ON or OFF ON: During control -
      Engine Revolutions Engine speed / min.: 0 r/min, max.: 65535 r/min Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
      Real Engine Torque Real engine torque / min.: -1024 N*m, max.: 1023 N*m - -
      Accelerator Opening Angle % The difference of a present accelerator / min.: 0%, max.: 128% When the accelerator pedal is released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
      Solenoid Relay ABS solenoid relay / ON or OFF

      ON: Solenoid relay ON

      OFF: Solenoid relay OFF

      		 -
      Motor Relay ABS motor relay / ON or OFF

      ON: Motor relay ON

      OFF: Motor relay OFF

      		 -
      Fail Safe Motor Relay ABS motor fail safe relay / ON or OFF

      ON: Motor relay ON

      OFF: Motor relay OFF

      		 -
      TRC/VSC Solenoid (SM2) Master cut solenoid (SM2) / ON or OFF ON: Operating -
      TRC/VSC Solenoid (SM1) Master cut solenoid (SM1) / ON or OFF ON: Operating -
      ABS Solenoid (SFRH) ABS solenoid (SFRH) / ON or OFF ON: Operating -
      ABS Solenoid (SFRR) ABS solenoid (SFRR) / ON or OFF ON: Operating -
      ABS Solenoid (SFLH) ABS solenoid (SFLH) / ON or OFF ON: Operating -
      ABS Solenoid (SFLR) ABS solenoid (SFLR) / ON or OFF ON: Operating -
      ABS Solenoid (SRRH) ABS solenoid (SRRH) / ON or OFF ON: Operating -
      ABS Solenoid (SRRR) ABS solenoid (SRRR) / ON or OFF ON: Operating -
      ABS Solenoid (SRLH) ABS solenoid (SRLH) / ON or OFF ON: Operating -
      ABS Solenoid (SRLR) ABS solenoid (SRLR) / ON or OFF ON: Operating -
      FR Speed Open Front speed sensor RH open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      FL Speed Open Front speed sensor LH open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      RR Speed Open Rear speed sensor RH open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      RL Speed Open Rear speed sensor LH open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      EFI Communication Open EFI communication open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      Yaw Rate Open Yaw rate sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      Deceleration Open Acceleration sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      Steering Open Steering angle sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      Master Cylinder Open Master cylinder pressure sensor open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      IG1 Voltage Value IG1 voltage / min.: 0 V, max.: 255 V 11 to 14 V -
      MT Voltage Value Motor driving monitor voltage / min.: 0 V, max.: 255 V - -
      TRC/VSC Off Mode VSC OFF switch / NORMAL, TRC OFF or VSC OFF

      NORMAL: Normal mode

      TRC OFF: TRC off mode

      VSC OFF: VSC off mode

      		 -
      Number of DTC Number of DTC recorded / min.: 0, max.: 255 - -
      IG Voltage Value Decreased IG voltage value decrease detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      IG Voltage Value Increased IG voltage value increase detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection / ERROR or NORMAL

      ERROR: Malfunction

      NORMAL: Normal

      		 -
      Brake Pedal Switch Open Brake pedal load sensing switch open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection / ERROR or NORMAL

      ERROR: Momentary interruption

      NORMAL: Normal

      		 -
      EFI Communication Invalid EFI communication invalid detection / ERROR or NORMAL

      ERROR: Invalid

      NORMAL: Normal

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    7. According to the display on the intelligent tester, perform the Active Test.

      ABS/VSC/TRC
      Tester Display Test Part Control Range Diagnostic Note
      ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter
      Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter
      Buzzer Skid control buzzer Buzzer ON/OFF Buzzer can be heard
      Solenoid Relay ABS solenoid relay Relay ON/OFF -
      Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard
      Stop Light Relay Stop light control (BRK-LP) relay Relay ON/OFF Stop lights come on
      ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      VSC/TRC Solenoid (SMR) Master cut solenoid (SM2) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      VSC/TRC Solenoid (SMF) Master cut solenoid (SM1) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard
      TRC OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter
      VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter
      Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter