FRONT SUSPENSION MEMBER INSTALLATION


  1. INSTALL POWER STEERING LINK ASSEMBLY


    1. A0160OM

      Install the power steering link assembly with the 2 bolts, 2 washers, and 2 nuts.

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

      Tech Tips

      Install the power steering link assembly together with the front suspension lower arm assembly.

  2. INSTALL FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    1. A01622QE01

      Install the front suspension lower arm assembly LH with the 2 bolts and washer.

      Torque:
      Bolt B
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }

      Tech Tips

      Install the power steering link assembly together with the front lower suspension arm assembly.

    2. A015ZOJ

      Set the front lower suspension arm in the horizontal position shown in the illustration.

    3. Fully tighten the bolt A.

      Torque:
      Bolt A
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }

      Note

      The final torque must be applied under standard vehicle height conditions.

  3. INSTALL FRONT LOWER SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as the LH side.

  4. INSTALL FRONT STABILIZER BAR


    1. A01633K

      Install the front stabilizer bar with the 2 nuts.

      Torque:
      84 N*m  { 857 kgf*cm, 62 ft.*lbf }

      Tech Tips

      If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

  5. INSTALL FRONT ENGINE MOUNTING INSULATOR


    1. A0163C4

      Install the 2 engine mounting insulators with the 2 nuts.

      Torque:
      70 N*m  { 714 kgf*cm, 52 ft.*lbf }

    2. Install the 2 engine mounting spacers.

  6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    1. A016283E01

      Install the front suspension crossmember sub-assembly with the 2 nuts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  7. INSTALL NO.2 EXHAUST MANIFOLD HEAT INSULATOR


    1. A0162AM

      Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Connect the air fuel ratio sensor connector.

  8. INSTALL NO.1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A01613Y

      Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Connect the air fuel ratio sensor connector.

  9. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY LH


    1. A0163B7

      Install the engine under cover sub-assembly LH to the front suspension crossmember sub-assembly with the 2 clamps.

  10. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH


    1. A015YHW

      Install the engine under cover sub-assembly RH to the front suspension crossmember sub-assembly with the 2 clamps.

  11. INSTALL OIL LEVEL DIPSTICK GUIDE


    1. A01633M

      Apply engine oil to a new O-ring, and install it to the oil level dipstick guide sub-assembly.

    2. Install the oil level dipstick guide sub-assembly with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  12. INSTALL OIL LEVEL DIPSTICK

  13. INSTALL ENGINE WITH TRANSMISSION ASSEMBLY

    Tech Tips

    Install the engine with transmission assembly. Click here