FRONT UPPER SUSPENSION ARM INSTALLATION

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure listed is for the LH side.


  1. INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY


    1. A01635IE01

      Temporarily install the front upper suspension arm assembly with the 2 bolts.

      Tech Tips

      When installing the front upper suspension arm assembly, temporarily tighten the bolts at the position shown in the illustration.

    2. A01608M

      Fully tighten the front upper suspension arm assembly with the 2 bolts.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

  2. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. A0162MR

      Install the front shock absorber with front coil spring and front No. 3 spring support reinforcement on the vehicle by tightening the 3 nuts on the suspension support side.

      Torque:
      67 N*m  { 683 kgf*cm, 49 ft.*lbf }
    2. A0162S1E01

      Insert the bolt from the rear of the vehicle, and install the front shock absorber lower side on the front lower suspension arm.

    3. Temporarily tighten the nut while holding the bolt.

      Tech Tips

      Fully tighten the nut after stabilizing the suspension.

    4. A0161LB

      Tighten a new lock nut.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  3. INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY


    1. A015YLJE01

      Install the steering knuckle to the front upper suspension arm assembly, and install them with the nut.

      Torque:
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }

    2. Install a new clip to the steering knuckle.

      Note


      • Further tighten the nut up to 60° if the holes for the clip are not aligned.

      • Do not loosen the nut to align the holes for the clip.

  4. INSTALL STEERING KNUCKLE WITH AXLE ASSEMBLY


    1. A015ZXD

      Install the steering knuckle with axle assembly to the front lower ball joint assembly with the 2 bolts.

      Torque:
      120 N*m  { 1223 kgf*cm, 89 ft.*lbf }

  5. INSTALL FRONT DISC


    1. A01603AE01

      Align the matchmarks of the disc and axle hub, and install the front disc.

      Note

      When replacing the disc with a new one, select the installation position where the front disc has minimal runout.

  6. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY


    1. A015YW2

      Install the front disc brake cylinder assembly with the 2 bolts.

      Torque:
      78 N*m  { 795 kgf*cm, 58 ft.*lbf }

      Note

      Do not twist the brake hose when installing the front disc brake cylinder assembly.

  7. CONNECT FRONT SPEED SENSOR


    1. A0160QX

      Connect the front speed sensor to the front shock absorber with coil spring with the 2 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

      Note


      • Do not twist the front speed sensor while installing it.

      • Be careful not to deform the bracket of the front shock absorber with coil spring when installing the bolts.

    2. Connect the front speed sensor connector.

  8. INSTALL FRONT STABILIZER LINK ASSEMBLY


    1. A0162CIE03

      Install the front stabilizer link assembly with the 2 nuts.

      Torque:
      84 N*m  { 857 kgf*cm, 62 ft.*lbf }

      Tech Tips

      If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

  9. STABILIZE SUSPENSION


    1. Install the front wheel.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    2. Lower the vehicle and bounce it up and down several times to stabilize the front suspension. Raise the vehicle.

    3. Remove the front wheel.

    4. A015ZOJ

      Jack up the front lower suspension arm placing a wooden block in between. Apply a load to the front suspension so that the front lower suspension arm is placed in a horizontal position.

  10. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    1. A015ZS0E02

      Fully tighten the bolt on the lower side of the front shock absorber while holding the nut.

      Torque:
      157 N*m  { 1601 kgf*cm, 116 ft.*lbf }

  11. INSTALL ENGINE ROOM SIDE COVER LH (for RHD)


    1. A015Z63

      Install the engine room side cover LH with the 4 clips.

  12. INSTALL ENGINE ROOM SIDE COVER LH (for LHD)


    1. A016120

      Install the engine room side cover LH with the 5 clips.

  13. INSTALL COOL AIR INTAKE DUCT SEAL


    1. A015ZFO

      Install the cool air intake duct seal with the 9 clips.

  14. INSTALL FRONT WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  15. CHECK FOR SPEED SENSOR SIGNAL

    Tech Tips

    Check for speed sensor signal. Click here

  16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Tech Tips

    Inspect and adjust front wheel alignment. Click here