TRANSMISSION WIRE INSTALLATION


  1. INSTALL TRANSMISSION WIRE


    1. A015Z5X

      Coat a new O-ring with ATF and install it to the transmission wire connector.

    2. Install the transmission wire.

    3. Using a 10 mm union nut wrench, install the bolt.

      Torque:
      without a union nut wrench
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      with a union nut wrench
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }

      Note

      Use a torque wrench with a fulcrum length of 185 mm (7.28 in.).

    4. A0161A9

      Connect the wire connector.

      Tech Tips

      Push up the lever until the claw of the transmission wire connector makes a connection sound.

    5. A0160CP

      Connect the 3 speed sensor connectors.

  2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. A0162EH

      Install the spring and check ball body.

    2. A016161E01

      Align the groove of the manual valve with the lever pin.

    3. A0162O6E01

      Install the 17 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt length
      21 mm (0.827 in.) for bolt A
      31 mm (1.22 in.) for bolt B
      64 mm (2.52 in.) for bolt C
    4. A015YZO

      Install the detent spring and detent spring cover with the bolt.

      Note

      Make sure to install the detent spring so that its roller is perpendicularly aligned to the center of the manual valve lever.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    5. A0161BB

      Connect the 9 connectors to the solenoid valves.

    6. Connect the oil pressure switch connector.

    7. Coat a new O-ring with ATF and install to the ATF temperature sensor.

    8. Install the ATF temperature sensor and lock plate with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    1. A015Z7EE01

      Coat a new O-ring with ATF and install it to the oil strainer.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. A015YHT

      Install the oil strainer to the valve body with the 4 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. A0160LAE01

      Install the 3 magnets to the oil pan.

    2. A0161ZN

      Install a new gasket and the oil pan to the transmission case with the 9 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note


      • A0162VKE01

      • Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.

      • Install the gasket so that there is no slack in the gasket, and that the entire seal surface is level.

      • Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.

      • When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area sleeve and the transmission seal surface.

  5. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY


    1. A0160GT

      Install the No. 1 exhaust pipe support bracket with the 2 bolts.

      Torque:
      43 N*m  { 439 kgf*cm, 32 ft.*lbf }
    2. A015YYGE01

      Install the No. 1 exhaust pipe support bracket with with 2 new bolts and 2 new nuts.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

  6. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

  7. INSTALL NO. 2 ENGINE UNDER COVER