AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P2817

DTC Code DTC Name
P2817 Pressure Control Solenoid "H" Performance or Stuck OFF (Shift Solenoid Valve SL5)

SYSTEM DESCRIPTION

Based on signals from the transmission speed sensors (NT, SP2 and NC3), the actual gear is detected.

If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, valve body and automatic transmission.

Tech Tips

Actual gear when a problem occurs in shift solenoid valve SL5:

TCM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SL5 stuck ON malfunction 2nd 2nd 3rd 4th 8th 6th 7th 8th
Actual gear during SL5 stuck OFF malfunction 1st N (1st)* 3rd 4th 5th 6th 7th N*

*: Neutral

DTC Code

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Malfunction Time

  4. Other

 Trouble Area
P2817

  1. ECT is 40°C (104°F) or more, ATF temperature is -10°C (14°F) or more, and vehicle is driven with shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), water temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. One of following occurs:


    1. When gear shifts to 1st are requested by TCM, actual gear changes to 2nd gear

    2. When gear shifts to 5th are requested by TCM, actual gear changes to 8th gear

  3. Malfunction status occurs once per trip

  4. 2 trip detection logic

  • Shift solenoid valve SL5

  • Valve body assembly

  • Automatic transmission assembly
P2817

  1. ECT is 40°C (104°F) or more, ATF temperature is -10°C (14°F) or more, and vehicle is driven with shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), water temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. When gear shifts to 2nd or 8th are requested by TCM, engine speed overruns (neutral status)

  3. Malfunction status continues for 0.5 sec. or more (1 trip)

  4. 2 trip detection logic

  • Shift solenoid valve SL5

  • Shift solenoid valve SLT

  • Valve body assembly

  • Automatic transmission assembly

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear position). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL.

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P2714 AND P2817)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECT / Trouble Codes.

    5. Read the DTCs using the intelligent tester.

      Result
      Display (DTC Output) Proceed to
      Only P2714 and P2817 are output A
      Only P2817 is output B
      P2714, P2817, and other DTCs are output C

      Tech Tips

      If any other codes besides P2714 and P2817 are output, perform troubleshooting for those DTCs first.


    B

    INSPECT SHIFT SOLENOID VALVE SL5 Click here

    C

    GO TO DTC CHART Click here

    A

  2. CLEAR DTC AND PERFORM STALL SPEED TEST


    1. Clear the DTCs Click here.

      Tech Tips

      Write down the currently output DTCs before clearing them.

    2. Perform the stall speed test Click here.

      Result
      Display (DTC Output) Proceed to
      Stall speed test can be performed A
      Stall speed test cannot be performed B

    B

    INSPECT SHIFT SOLENOID VALVE SLT Click here

    A

  3. INSPECT SHIFT SOLENOID VALVE SL5


    1. A0161CGE10

      Remove the shift solenoid valve SL5 Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SL5 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Result Proceed to
      OK B
      NG A

    B

    INSPECT TRANSMISSION VALVE BODY ASSEMBLY Click here

    A

    REPLACE SHIFT SOLENOID VALVE SL5 Click here

  4. INSPECT SHIFT SOLENOID VALVE SLT


    1. A0161CGE04

      Remove the shift solenoid valve SLT Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SLT - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.

    NG

    REPLACE SHIFT SOLENOID VALVE SLT Click here

    OK

  5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Check the transmission valve body assembly Click here.

      OK
      There are no foreign objects on any valve.

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

    REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY Click here