AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P0776

DTC Code DTC Name
P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2)

SYSTEM DESCRIPTION

Based on signals from the transmission speed sensors (NT, SP2 and NC3), the actual gear is detected.

If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, valve body and automatic transmission.

Tech Tips

Actual gear when a problem occurs in shift solenoid valve SL2:

TCM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SL2 stuck ON malfunction 5th 8th 7th 6th 5th 6th 7th 8th
Actual gear during SL2 stuck OFF malfunction 1st 2nd 3rd 4th N (1st)* N* N* N*

*: Neutral

DTC Code

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Malfunction Time

  4. Other

 Trouble Area
P0776

  1. ECT is 40°C (104°F) or more, ATF temperature is -10°C (14°F) or more, and vehicle is driven with shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), water temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. One of following occurs:


    1. When gear shifts to 1st are requested by TCM, actual gear changes to 5th gear

    2. When gear shifts to 2nd are requested by TCM, actual gear changes to 8th gear

    3. When gear shifts to 4th are requested by TCM, actual gear changes to 6th gear

  3. Malfunction status occurs 2 times per trip

  4. 2 trip detection logic

  • Shift solenoid valve SL2

  • Valve body assembly

  • Automatic transmission assembly
P0776

  1. ECT is 40°C (104°F) or more, ATF temperature is -10°C (14°F) or more, and vehicle is driven with shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, speed sensors (NT, NC3, SP2), water temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. When gear shifts to 5th to 8th are requested by TCM, engine speed overruns (neutral status)

  3. Malfunction status continues for 0.5 sec. or more (1 trip)

  4. 2 trip detection logic

  • Shift solenoid valve SL2

  • Shift solenoid valve SR

  • Shift solenoid valve SLT

  • Valve body assembly

  • Automatic transmission assembly

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear position). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL.

WIRING DIAGRAM

Refer to DTC P2765 Click here.

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P0771, P0776 AND P2714)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECT / Trouble Codes.

    5. Read the DTCs using the intelligent tester.

      Result
      Display (DTC Output) Proceed to
      Only P0771, P0776 and P2714 are output A
      Only P0776 is output B
      P0771, P0776, P2714, and other DTCs are output C

      Tech Tips

      If any other codes besides P0771, P0776 and P2714 are output, perform troubleshooting for those DTCs first.


    B

    INSPECT SHIFT SOLENOID VALVE SL2 Click here

    C

    GO TO DTC CHART Click here

    A

  2. CLEAR DTC AND PERFORM STALL SPEED TEST


    1. Clear the DTCs Click here.

      Tech Tips

      Write down the currently output DTCs before clearing them.

    2. Perform the stall speed test Click here.

      Result
      Test Condition Proceed to
      Stall speed test can be performed A
      Stall speed test cannot be performed B

    B

    INSPECT SHIFT SOLENOID VALVE SLT Click here

    A

  3. CLEAR DTC AND PERFORM RUNNING TEST


    1. Clear the DTCs Click here.

      Tech Tips

      Write down the currently output DTCs before clearing them.

    2. Start the engine, drive the vehicle and perform the inspection.

      Result
      Test Condition Proceed to

      • Gear cannot be shifted between 1st gear and 4th gear

      • Gear can only be shifted from 4th gear to 5th gear

      • Gear cannot be shifted between 5th gear and 8th gear*

      		 A

      • Gear can be shifted from 1st gear to 4th gear

      • For 5th gear and above, gear shifts to neutral

      		 B
      Conditions other than those listed above C

      Tech Tips

      *: If the gear is shifted to 5th gear or above, gear shifts will no longer be able to be performed. When performing the test again, first clear the DTCs.


    B

    INSPECT SHIFT SOLENOID VALVE SL2 Click here

    C

    INSPECT SPEED SENSOR TERMINAL (NC3 TERMINAL) Click here

    A

  4. INSPECT SHIFT SOLENOID VALVE SR


    1. A0162LXE01

      Remove the shift solenoid valve SR Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Shift solenoid SR connector - Shift solenoid SR body 20°C (68°F) 11 to 15 Ω

    3. Connect a battery positive (+) lead to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Result Proceed to
      OK B
      NG A

    B

    INSPECT TRANSMISSION VALVE BODY ASSEMBLY Click here

    A

    REPLACE SHIFT SOLENOID VALVE SR Click here

  5. INSPECT SHIFT SOLENOID VALVE SL2


    1. A0161CGE06

      Remove the shift solenoid valve SL2 Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SL2 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Result Proceed to
      OK B
      NG A

    B

    INSPECT TRANSMISSION VALVE BODY ASSEMBLY Click here

    A

    REPLACE SHIFT SOLENOID VALVE SL2 Click here

  6. INSPECT SHIFT SOLENOID VALVE SLT


    1. A0161CGE04

      Remove the shift solenoid valve SLT Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SLT - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.

    NG

    REPLACE SHIFT SOLENOID VALVE SLT Click here

    OK

  7. INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Check the transmission valve body assembly Click here.

      OK
      There are no foreign objects on any valve.

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

    REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY Click here

  8. INSPECT SPEED SENSOR TERMINAL (NC3 TERMINAL)


    1. A015ZNTE14

      Disconnect the transmission wire connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      E47-11 (NC3B) - Body ground Engine switch on (IG) 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E47-12 (NC3O) - Body ground Always 99 to 101 Ω

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) Click here

    OK

  9. INSPECT TRANSMISSION WIRE (SPEED SENSOR NC3)


    1. A0160QFE03

      Disconnect the speed sensor (NC3) connector Click here.

    2. Disconnect the transmission wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the speed sensor (NC3) connector - 11 (NC3B) Always Below 1 Ω
      Terminal 2 of the speed sensor (NC3) connector - 12 (NC3O) Always Below 1 Ω
      Terminal 1 of the speed sensor (NC3) connector or 11 (NC3B) - Body ground Always 10 kΩ or higher
      Terminal 2 of the speed sensor (NC3) connector or 12 (NC3O) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

    OK

    REPLACE SPEED SENSOR Click here

  10. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    1. A016249E31

      Disconnect the transmission wire connector.

    2. Disconnect the TCM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E47-11 (NC3B) - E59-19 (NC3B) Always Below 1 Ω
      E47-12 (NC3O) - E59-18 (NC3O) Always Below 1 Ω
      E47-11 (NC3B) or E59-19 (NC3B) - Body ground Always 10 kΩ or higher
      E47-12 (NC3O) or E59-18 (NC3O) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. REPLACE TCM


    1. Replace the TCM Click here.


    NEXT

    PERFORM A/T CODE REGISTRATION Click here