AUTOMATIC TRANSMISSION SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Powertrain / ECT / Data List.

    7. According to the display on the intelligent tester, read the Data List.

      TCM
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed

      Vehicle speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual vehicle speed Speed indicated on speedometer
      Engine Speed

      Engine speed/

      Min.: 0 rpm

      Max.: 16383.75 rpm

      		 Idling: 550 to 800 rpm -
      Calculate Load

      Calculated load/

      Min.: 0%

      Max.: 100%

      • Idling: 15.0 to 35.0%

      • Running without load (2000 rpm): 10.0 to 30.0%

      		 -
      Coolant Temp

      Engine coolant temperature/

      Min.: -40°C (-40°F)

      Max.: 140°C (284°F)

      		 After warming up: 80 to 105°C (176 to 221°F)

      If value -40°C (-40°F): sensor circuit open

      If value 140°C (284°F): sensor circuit shorted
      Engine Run Time

      Engine run time/

      Min.: 0 seconds

      Max.: 65535 seconds

      		 Time after engine start -
      Battery Voltage

      Battery voltage/

      Min.: 0, Max.: 65.535 V

      		 Always: 11 to 14 V -
      Throttle Sensor Volt %

      Absolute throttle position/

      Min.: 0%

      Max.: 100%

      Throttle is fully


      • Closed: 10 to 24%

      • Open: 64 to 96%

      		 -
      Starter Signal

      Starter signal/

      ON or OFF

      Engine is


      • ON: Cranking

      • OFF: Not cranking

      		 -
      Stop Light Switch

      Stop light switch status/

      ON or OFF

      Brake pedal is


      • ON: Depressed

      • OFF: Released

      		 -
      TC Terminal

      TC Terminal status/

      ON or OFF

      		 - -
      #Codes (Include History)

      # of Codes /

      Min.: 0

      Max.: 255

      		 - Number of detected DTCs
      MIL ON Run Distance

      MIL ON run distance/

      Min.: 0 km (0 mile)

      Max.: 65535 km (40723 mile)

      		 Distance after DTC detected -
      Running Time from MIL ON

      Running time from MIL ON/

      Min.: 0 minutes

      Max.: 65535 minutes

      		 Equivalent to running time after MIL ON -
      Time after DTC Cleared

      Time after DTC cleared /

      Min.: 0 minutes

      Max.: 65535 minutes

      		 Equivalent to time after DTCs cleared -
      Distance from DTC Cleared

      Distance after DTC cleared /

      Min.: 0 km (0 mile)

      Max.: 65535 km (40723 mile)

      		 Equivalent to time after DTCs cleared -
      Warmup Cycle Cleared DTC

      Warm-up cycle after DTC cleared /

      Min.: 0, Max.: 255

      		 - Number of warm-up cycles after DTCs cleared
      TC and TE1

      TC and TE1 terminals of DLC3/

      ON or OFF

      		 - Active Test support data
      Engine Speed from EFI

      Engine speed/

      Min.: 0 rpm

      Max.: 16383.75 rpm

      		 Idling: 550 to 800 rpm Engine speed received from ECM
      Intake-Air Temp from EFI

      Intake air temperature/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      		 Equivalent to ambient air temperature Engine speed received from ECM
      Coolant Temp from EFI

      Engine coolant temperature/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      		 After warming up: 80 to 105°C (176 to 221°F) Engine speed received from ECM
      Throttle Position from EFI

      Throttle sensor positioning/

      Min.: 0%

      Max.: 100%

      		 Idling: 0 to 10% Engine speed received from ECM
      Accel Position from EFI

      Accelerator sensor positioning/

      Min.: 0%

      Max.: 100%

      		 Idling: 0 to 10% Engine speed received from ECM
      SPD (NT)

      Input shaft speed/

      Min.: 0 rpm

      Max.: 12750 rpm

      Lock-up is


      • ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

      • OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed

      		 Data is displayed in increments of 50 rpm
      SPD (SP2)

      Output shaft speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      Vehicle stopped: 0 km/h (0 mph)

      (output shaft speed is equal to vehicle speed)

      		 -
      Shift SW Status (P Range)

      Park/neutral position switch status/

      ON or OFF

      • ON: Shift lever is in P

      • OFF: Shift lever is not in P

      When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Shift SW Status (R Range)

      Park/neutral position switch status/

      ON or OFF

      • ON: Shift lever is in R

      • OFF: Shift lever is not in R

      When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Shift SW Status (N Range)

      Park/neutral position switch status/

      ON or OFF

      • ON: Shift lever is in N

      • OFF: Shift lever is not in N

      When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      Sports Shift Up SW

      Sport shift up switch status/

      ON or OFF

      • ON: Continuously shift to "+" (up-shift)

      • OFF: Release "+" (up-shift)

      		 -
      Sports Shift Down SW

      Sport shift down switch status/

      ON or OFF

      • ON: Continuously shift to "-" (down-shift)

      • OFF: Release "-" (down-shift)

      		 -
      Sports Mode Selection SW

      Sport (M) mode select switch status/

      ON or OFF

      Shift lever is:


      • ON: M, "+" or "-"

      • OFF: Not in M, "+" or "-"

      		 -
      Shift SW Status (D Range)

      Park/neutral position switch status/

      ON or OFF

      • ON: Shift lever is in D or M

      • OFF: Shift lever is not in D or M

      When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, refer to DTC P0705 Click here.
      A/T Oil Temperature 1

      ATF temperature sensor value/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      • After stall speed test: Approximately 80°C (176°F)

      • While engine is cold:

        Equal to ambient temperature

      		 If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
      NT Sensor Voltage

      NT sensor voltage/

      Min.: 0 V

      Max.: 5 V

      		 Idling: 0.1 to 1.9 V -
      SP2 Sensor Voltage

      SP2 sensor voltage/

      Min.: 0 V

      Max.: 5 V

      		 Idling: 0.1 to 1.9 V -
      TPS 1 Switch

      Oil pressure switch status/

      ON or OFF

      • ON: Gear is 1st to 5th

      • OFF: Gear is 6th to 8th; or shift lever is in P, N or R

      		 -
      SPD (NC3)

      No. 3 clutch drum speed/

      Min.: 0 rpm

      Max.: 12750 rpm

      • 0 rpm: 2nd or 8th gear

      • above 0 rpm: 1st, or 3rd to 7th gear

      		 Data is displayed in increments of 50 rpm
      NC3 Sensor Voltage

      NC3 Sensor Voltage/

      Min.: 0 V

      Max.: 5 V

      		 Idling: 0.1 to 1.9 V -
      Lock Up

      Lock up/

      ON or OFF

      Lock-up is


      • ON: Operating

      • OFF: Not operating

      		 -
      Shift Status

      TCM gear shift command/

      1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th

      Shift lever is


      • In D: 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th

      • In M: 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th

      		 -
      SLT Solenoid Status

      Shift solenoid SLT status/

      ON or OFF

      • OFF: Accelerator pedal is depressed

      • ON: Accelerator pedal is released

      		 -
      SLU Solenoid Status

      Shift solenoid SLU status/

      ON or OFF

      Shift solenoid SLU is


      • ON: Operating

      • OFF: Not operating

      		 -
      SL Solenoid Status

      Shift Solenoid SL Status/

      ON or OFF

      Shift solenoid SL is


      • ON: Operating

      • OFF: Not operating

      		 -
      AT Fluid

      Flex lockup judder judgment/

      ON or OFF

      • ON: Judder judgment occurs

      • OFF: Judder judgment does not occur

      		 -

    8. Enter the following menus: Powertrain / Engine / Data List.

    9. According to the display on the intelligent tester, read the Data List.

      ECM
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Pattern Switch (PWR/M)

      Pattern select switch (SPORT) status/

      ON or OFF

      Engine switch is:

      ON: OFF

      ↓

      Pattern select switch (SPORT) is:

      Pushed: ON

      ↓

      Pattern select switch (SPORT) is:

      Pushed: OFF

      		 -
      Kick Down Switch Status Kick Down Switch Status/ON or OFF

      Accelerator Pedal is:


      • Fully depressed: ON

      • Released: OFF

      		 -
      Snow or 2nd Start Mode

      Pattern select switch (SNOW) status/

      ON or OFF

      Engine switch is:

      ON: OFF

      ↓

      Pattern select switch (SNOW) is:

      Pushed: ON

      ↓

      Pattern select switch (SNOW) is:

      Pushed: OFF

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the intelligent tester on.

    6. Enter the following menus: Powertrain / ECT / Active Test.

    7. According to the display on the intelligent tester, perform the Active Test.

      TCM
      Tester Display Test Part Control Range Diagnostic Note
      Connect the TC and TE1

      Connects and disconnects TC and TE1.

      (transitions into the fluid temperature detection mode)

      		 ON or OFF -
      Activate the solenoid (SLU) Operate the shift solenoid SLU ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the solenoid (SLT)* Operate the shift solenoid SLT and raise line pressure

      ON or OFF

      Tech Tips


      • OFF: Line pressure up (when Active Test "Activate the solenoid (SLT)" is performed, TCM commands SLT solenoid to turn OFF)

      • ON: No action (normal operation)

      [Vehicle Condition]


      • Vehicle stopped

      • Engine idling
      Activate the Lock Up Control shift solenoid SLU to set automatic transmission to lock-up condition ON or OFF

      Possible to check shift solenoid valve SLU operation

      [Vehicle Condition]


      • Throttle valve opening angle: Less than 35%

      • Vehicle speed: 60 km/h (37 mph) or more
      Activate the Solenoid (SL) Operate the shift solenoid SL ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Control the Shift Position Operate shift solenoid valves to select gears

      • Press "→" button: Shift up

      • Press "←" button: Shift down

      Possible to check operation of shift solenoid valves

      [Vehicle Condition]


      • 50 km/h (31 mph) or less
      Activate the Solenoid (SR) Operate the shift solenoid SR ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL1) Operate the shift solenoid SL1 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL2) Operate the shift solenoid SL2 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL3) Operate the shift solenoid SL3 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL4) Operate the shift solenoid SL4 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (SL5) Operate the shift solenoid SL5 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N

      *: The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test Click here.

      Tech Tips

      Note that the pressure readings for the Active Test and Hydraulic Test are different.