ENGINE SWITCH REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A0161BO

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  3. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A016226

      Using a moulding remover, disengage the claw.

    2. A0161ZW

      Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  4. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A015YLQ

      Using a moulding remover, disengage the claw.

    2. A0160CR

      Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  5. REMOVE CONSOLE PANEL SUB-ASSEMBLY


    1. A0160RU

      Hold the front of the console panel sub-assembly as shown in the illustration and disengage the 8 clips by pulling the console panel sub-assembly in the direction shown by the arrow.

      Note

      Do not use any tools to disengage the clips. The use of tools may result in damage to the console panel sub-assembly.

    2. Disconnect the connectors and remove the console panel sub-assembly.

  6. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. A0160IR

      Remove the 2 screws <E>.

    2. A0160OX

      Pull the front ash receptacle assembly in the direction indicated by the arrow to disconnect the connectors and remove it.

  7. REMOVE REAR ASH RECEPTACLE ASSEMBLY


    1. Remove the rear ash receptacle assembly.

  8. REMOVE CONSOLE BOX REGISTER ASSEMBLY


    1. A0161O8

      Disengage the 2 claws and 4 clips, and then remove the console box register assembly.

  9. REMOVE CONSOLE BOX


    1. A0160S1

      Remove the 2 bolts.

    2. Disconnect the 2 connectors.

    3. Disengage the 2 clamps.

    4. A0162NA

      Remove the 2 bolts.

    5. Disconnect the connector.

    6. A015ZEK

      Remove the 2 bolts.

    7. A0162J5

      Disengage the 2 claws and 2 clips, and then remove the console box.

  10. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A0163DOE02

      Using a screwdriver, disengage the 4 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A015ZH6E03

      Apply protective tape to the areas shown in the illustration.

    3. A015ZAL

      Using a moulding remover, disengage the 4 claws starting from the right of the No. 3 instrument panel register assembly. Disengage the remaining 3 claws by pulling the No. 3 instrument panel register assembly by hand.

      Note

      Do not pry the lower part of the No. 3 instrument panel register assembly. Doing so may damage the assembly.

    4. Disconnect the connectors.

  11. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A0160YT

      Disengage the 4 claws and remove the center lower instrument cluster finish panel.

  12. REMOVE MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System)


    1. A0162FS

      Remove the 4 bolts.

    2. Pull the multi-display with radio receiver assembly toward the rear of the vehicle.

    3. Disconnect each connector and remove the multi-display.

  13. REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System)


    1. A015ZQC

      Remove the 4 bolts.

    2. Pull the integration control panel with radio receiver assembly toward the rear of the vehicle.

    3. Disconnect each connector and remove the panel.

  14. REMOVE ENGINE SWITCH


    1. A015ZVH

      Disconnect the switch connector.

    2. Detach the 2 claws and remove the switch.