IGNITION COIL AND SPARK PLUG REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A0160IP

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the 2 clips on the rear of the cover and remove the V-bank cover sub-assembly.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  3. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A015ZFO

      Remove the 9 clips and cool air intake duct seal.

  4. REMOVE ENGINE ROOM SIDE COVER LH (for LHD)


    1. A016120

      Remove the 5 clips and engine room side cover LH.

  5. REMOVE ENGINE ROOM SIDE COVER LH (for RHD)


    1. A015Z63

      Remove the 4 clips and engine room side cover LH.

  6. REMOVE ENGINE ROOM SIDE COVER RH (for LHD)


    1. A0161AL

      Remove the 3 clips and engine room side cover RH.

  7. REMOVE ENGINE ROOM SIDE COVER RH (for RHD)


    1. A015YK3

      Remove the 4 clips and engine room side cover RH.

  8. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A015YRW

      Loosen the 2 hose clamps and separate the 2 ventilation hoses.

    2. A01622I

      Disconnect the mass air flow meter connector and separate the wire harness clamp.

    3. A015ZWF

      Loosen the hose clamp and separate the air cleaner hose.

    4. A015YT4

      Unlock the 2 clamps and remove the air cleaner cap sub-assembly.

  9. REMOVE BATTERY (for LHD)


    1. A0162W7

      Disconnect the 2 clamps.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Remove the nut and the battery clamp.

    4. Remove the battery insulator.

    5. Remove the battery.

  10. REMOVE BATTERY (for RHD)


    1. A0163BE

      Disconnect the 2 clamps.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Remove the nut and the battery clamp.

    4. Remove the battery insulator.

    5. Remove the battery.

  11. REMOVE NO. 1 BATTERY TRAY SUPPORT

  12. REMOVE POWER STEERING ECU ASSEMBLY


    1. Release the locks of the 2 power steering ECU assembly connectors (A) and (B).

      A01625SE01

    2. Disconnect the connectors (A), (B) and (C) from the power steering ECU assembly.

    3. A016155

      Remove the 3 bolts.

    4. Remove the power steering ECU assembly.

  13. REMOVE BATTERY TRAY (for LHD)


    1. A0163HY

      Remove the 3 bolts and battery tray.

    2. A016319

      Remove the 2 bolts and nut and separate the No. 7 engine room relay block.

  14. REMOVE BATTERY TRAY (for RHD)


    1. A015ZVG

      Remove the 3 bolts and battery tray.

    2. A0162TN

      Remove the 2 bolts and nut and separate the No. 7 engine room relay block.

  15. REMOVE WIRE HARNESS CLAMP BRACKET (for LHD)


    1. A0162F8

      Remove the bolt and separate the wire harness clamp bracket.

    2. Separate the wire harness clamp from the wire harness clamp bracket.

  16. REMOVE WIRE HARNESS CLAMP BRACKET (for RHD)


    1. A015Z8N

      Remove the bolt and separate the wire harness clamp bracket.

    2. Separate the wire harness clamp from the wire harness clamp bracket.

  17. REMOVE IGNITION COIL ASSEMBLY


    1. Disconnect the 8 ignition coil connectors.

    2. A0160Z7E01

      Remove the 8 bolts and 8 ignition coil assemblies.

      Note

      Do not damage the ignition coil assemblies when removing them.

  18. REMOVE SPARK PLUG


    1. A0162KA

      Using a 16 mm plug wrench, remove the 8 spark plugs.