SFI SYSTEM, Diagnostic DTC:P1364, P1365

DTC Code DTC Name
P1364 "C" Camshaft Position Actuator Circuit Open, Low, High Bank1
P1365 "C" Camshaft Position Actuator Circuit Open, Low, High Bank2

DESCRIPTION

Refer to DTC P0010 Click here.

DTC No. DTC Detection Condition Trouble Area
P1364

While engine switch is on (IG) or engine is running, open or short in VTM and VTP terminals of camshaft timing control motor is detected for 3 seconds

(1 trip detection logic)

  • Camshaft timing control motor (bank 1)

  • Power supply of camshaft timing control motor (bank 1)

  • Wire harness or connector
P1365

While engine switch is on (IG) or engine is running, open or short in VTM and VTP terminals of camshaft timing control motor is detected for 3 seconds

(1 trip detection logic)

  • Camshaft timing control motor (bank 2)

  • Power supply of camshaft timing control motor (bank 2)

  • Wire harness or connector

MONITOR DESCRIPTION

This DTC is output when a power supply malfunction, diagnostic signal malfunction or motor operation signal malfunction is detected in the intake side camshaft timing control motor. The camshaft timing control motor is equipped with a self diagnostic function, which is used to send diagnostic a signal (VTM) to the ECM. If the ECM receives a VTP or VTM open signal, a DTC is output immediately (1 trip detection logic).

If the engine is idled for 10 seconds, a DTC is detected.

WIRING DIAGRAM

Refer to DTC P1360 Click here.

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT VVT RELAY (VVT LH, VVT RH)


    1. A01602O

      Remove the VVT LH relay or VVT RH relay from the engine room No. 2 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω

    3. Reinstall the relay.


    NG

    REPLACE VVT RELAY (VVT LH, VVT RH)

    OK

  2. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR POWER SOURCE)


    1. A015ZXFE27

      Disconnect the camshaft timing control motor connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      E61-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V
      E65-1 (+B) - Body ground

    4. Reconnect the camshaft timing control motor connector.


    NG

    CHECK HARNESS AND CONNECTOR (VVT LH OR VVT RH RELAY POWER SOURCE) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ENGINE GROUND)


    1. A015ZXFE26

      Turn the engine switch off.

    2. Disconnect the camshaft timing control motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E61-2 (PGND) - Engine ground Always Below 1 Ω
      E65-2 (PGND) - Engine ground

    4. Reconnect the camshaft timing control motor connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ENGINE GROUND)

    OK

  4. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ECM)


    1. A015YKGE11

      Disconnect the camshaft timing control motor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      E62-1 (VTM) - E5-9 (EMD1) Always Below 1 Ω
      E62-5 (VTP) - E5-8 (EDT1)
      E64-1 (VTM) - E4-31 (EMD2)
      E64-5 (VTP) - E4-16 (EDT2)
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      E62-1 (VTM) or E5-9 (EMD1) - Body ground Always 10 kΩ or higher
      E62-5 (VTP) or E5-8 (EDT1) - Body ground
      E64-1 (VTM) or E4-31 (EMD2) - Body ground
      E64-5 (VTP) or E4-16 (EDT2) - Body ground

    4. Reconnect the camshaft timing control motor connector and ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ENGINE GROUND)


    1. A015ZI9E02

      Disconnect the camshaft timing control motor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E62-4 (SGND) - Engine ground Always Below 1 Ω
      E64-4 (SGND) - Engine ground

    3. Reconnect the camshaft timing control motor connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ENGINE GROUND)

    OK

  6. REPLACE CAMSHAFT TIMING CONTROL MOTOR (BANK 1 OR BANK 2)


    1. Replace the camshaft timing control motor Click here.


    NEXT

  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and idle it for 10 seconds.

    3. Enter the following menus: Powertrain / Engine / DTC.

    4. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      Other DTCs are output B

    B

    GO TO DTC CHART Click here

    A

    END

  8. CHECK HARNESS AND CONNECTOR (VVT LH OR VVT RH RELAY POWER SOURCE)


    1. A015Z10E02

      Remove the VVT LH or VVT RH relay.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      VVT LH relay (1) - Body ground Engine switch on (IG) 11 to 14 V
      VVT RH relay (1) - Body ground Engine switch on (IG) 11 to 14 V

    4. Reinstall the relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 2 FUSE - VVT LH OR VVT RH RELAY)

    OK

  9. CHECK HARNESS AND CONNECTOR (VVT LH OR VVT RH RELAY - BODY GROUND)


    1. A015Z10E02

      Remove the VVT LH or VVT RH relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      VVT LH relay (2) - Body ground Always Below 1 Ω
      VVT RH relay (2) - Body ground Always Below 1 Ω

    3. Reinstall the relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT LH OR VVT RH RELAY - BODY GROUND)

    OK

  10. INSPECT FUSIBLE LINK BLOCK ASSEMBLY (VVT FUSE)


    1. A015ZLLE07

      Remove the fusible link block from the engine room No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1F-4 - 1B-1 Always Below 1 Ω

    3. Reinstall the fusible link block assembly.


    NG

    REPLACE FUSIBLE LINK BLOCK ASSEMBLY (VVT FUSE)

    OK

  11. CHECK HARNESS AND CONNECTOR (VVT LH OR VVT RH RELAY - BATTERY)


    1. A015Z10E02

      Remove the VVT LH or VVT RH relay.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      VVT LH relay (3) - Body ground Engine switch on (IG) 11 to 14 V
      VVT RH relay (3) - Body ground Engine switch on (IG) 11 to 14 V

    4. Reinstall the relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT LH OR VVT RH RELAY - BATTERY)

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT LH OR VVT RH RELAY - CAMSHAFT TIMING CONTROL MOTOR)