NAVIGATION SYSTEM (for HDD) Reverse Signal Circuit

DESCRIPTION

The display and navigation module display receives a reverse signal from the main body ECU LH (cowl side junction block LH) and information about the navigation antenna, and then adjusts the vehicle position on the navigation display. The ECM sends a reverse signal based on the shift position signal received from the park/neutral position switch assembly. The reverse signal sent from the ECM is received by the main body ECU LH (cowl side junction block LH) via the network gateway ECU using CAN communication and BEAN communication.

WIRING DIAGRAM

A0163GKE02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)


    1. Disconnect the J122 display and navigation module display connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J122-16 (REV) - Body ground

      Engine switch on (IG)

      Shift lever in R

      		 11 to 14 V
      J122-16 (REV) - Body ground

      Engine switch on (IG)

      Shift lever in any position except R

      		 Below 1 V

    NG

    CHECK HARNESS AND CONNECTOR Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK HARNESS AND CONNECTOR


    1. Disconnect the J122 display and navigation module display connector.

    2. Disconnect the Q2 main body ECU LH (cowl side junction block LH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J122-16 (REV) - Q2-2 (BACK) Always Below 1 Ω
      J122-16 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. READ VALUE USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECT / Data List.

    5. According to the display on the intelligent tester, read the "Data List".

      ECM
      Tester Display Test Part Control Range Diagnostic Note
      Shift SW Status (R Range)

      Park/neutral position switch status/

      ON or OFF

      Shift lever is:


      • In R: ON

      • Not in R: OFF

      		 When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect
      OK
      Shift Lever Position Display
      R ON
      Except R OFF

    NG

    GO TO AUTOMATIC TRANSMISSION SYSTEM (for AA80E) Click here

    OK

  4. REPLACE MAIN BODY ECU LH (COWL SIDE JUNCTION BLOCK LH)


    1. Replace the main body ECU LH (cowl side junction block LH).

    2. A0161RH

      Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check Click here.

    3. Check that the display changes between ON and OFF according to the shift lever operation.

      OK
      Shift Lever Position Display
      Except R OFF
      R ON

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.


    NG

    REPLACE NETWORK GATEWAY ECU Click here

    OK

    END

  5. REPLACE NETWORK GATEWAY ECU


    1. Replace the network gateway ECU Click here.

    2. A0161RH

      Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check Click here.

    3. Check that the display changes between ON and OFF according to the shift lever operation.

      OK
      Shift Lever Position Display
      Except R OFF
      R ON

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.


    NG

    REPLACE ECM (for 2UR-GSE) Click here

    OK

    END