NAVIGATION SYSTEM (for DVD) OPERATION CHECK


  1. CHECK SYSTEM NORMAL CONDITION


    1. If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

      Symptom Answer
      A longer route than expected is chosen. Depending on the road conditions, the display and navigation module display may determine that a longer route is quicker.
      Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
      When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the actual position. If the vehicle starts before the navigation system activates, the system may not react.
      When running on certain types of roads, especially new roads, the vehicle position deviates from the actual position. When the vehicle is driving on new roads not available on the map disc, the system attempts to match it to another nearby road, causing the position mark to deviate.
    2. A01607Z

      The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or display and navigation module display.


      1. The current position mark may be displayed on a nearby parallel road.

      2. A0161BI

        Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

      3. A0162IC

        When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

      4. A0162AN

        When the vehicle is carried, such as on a ferry, and the vehicle itself is not running, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by GPS.

      5. A0162OV

        When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

      6. A01608B

        When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees) the current vehicle position mark may deviate from the correct position.

      7. A0161F5

        When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

      8. A0162JYE03

        When the engine switch is turned on (ACC or IG) on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

      9. A0160E7

        When the vehicle travels on a snowy road or a mountain path with the chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

      10. A0161UX

        When the tires are changed, the current vehicle position mark may deviate from the correct position.

        Tech Tips


        • A change in tire diameter may cause a speed sensor error.

        • Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.

  2. CHECK PANEL & STEERING SWITCH

    Tech Tips


    • The display and navigation module display panel switches, radio receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01614X

      Select "Panel & Steering Switch" from the "Function Check/Setting" screen.

    4. Panel & Steering Switch Check Mode


      1. A015Z7YE01

        Operate each switch and check that the switch names and condition are correctly displayed.

        Screen Description
        Display Content
        *1: Push switch name

        • Name of the pressed switch is displayed.

        • If more than one switch is pressed, "MULTIPLE" will be displayed.
        *2: Rotary switch name Name of the rotary switch is displayed.
        *3: Rotary switch direction Direction of the rotary switch is displayed.

  3. CHECK TOUCH SWITCH

    Tech Tips


    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0161QE

      Select "Touch Switch" from the "Function Check/Setting" screen.

    4. A016235

      Touch Switch Check


      1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tech Tips


        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after the finger is removed.

  4. CHECK MIC & VOICE RECOGNITION

    Tech Tips


    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A015YVC

      Select "Mic & Voice Recognition" from the "Function Check/Setting" screen.

    4. Microphone & Voice Recognition Check


      1. A015ZJTE01

        When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      2. Push the recording switch and perform voice recording.

      3. Check that the recording indicator remains on while recording and that the recording can be played normally.

        Tech Tips


        • For details of this function, refer to Diagnosis Display Detailed Description Click here.

        • This function is controlled by the display and navigation module display (built-in navigation ECU).

  5. CHECK COLOR BAR

    Tech Tips


    • The display color on the screen is checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0161T7

      Select "Color Bar" from the "Function Check/Setting" screen.

    4. Color Bar Check Mode


      1. A01625E

        Select a color bar from the "Color Bar Check Mode" screen.

      2. Check the display color.

        Tech Tips


        • The entire screen turns to the color or stripe selected.

        • Touching the display will return to the "Color Bar Check" screen.

  6. CHECK GPS & VEHICLE SENSORS

    Tech Tips


    • GPS information, vehicle signals and sensor signals are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A015ZZI

      Select "GPS&Vehicle Sensors" from the "Function Check/Setting" screen.

    4. GPS information


      1. A016138

        When GPS information is displayed, check the GPS conditions.

        Tech Tips


        • This screen is updated once per second when input signals to the vehicle are changed.

        • For details of this function, refer to Diagnosis Display Detailed Description Click here.

    5. Select "Sensors Check" from the "GPS Information" screen.

    6. Vehicle Sensors


      1. A016146

        Check all the signals and sensors when vehicle signal information is displayed.

        Tech Tips


        • This screen is updated once per second when input signals to the vehicle are changed.

        • This screen displays vehicle signals input to the display and navigation module display (built-in navigation ECU).

        • For details of this function, refer to Diagnosis Display Detailed Description Click here.

  7. CHECK VEHICLE SIGNAL

    Tech Tips


    • Vehicle signals received by the display and navigation module display are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0160WK

      Select "Vehicle Signal" from the "Function Check/Setting" screen.

    4. Vehicle Signal Check Mode


      1. A0162NG

        When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

        Tech Tips


        • Only conditions having inputs are displayed.

        • This screen displays vehicle signals input to the display and navigation module display.

        • For details of this function, refer to Diagnosis Display Detailed Description Click here.

  8. CHECK HANDS-FREE VOLUME SETTING

    Tech Tips


    • The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A0163BH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A0161W5

      Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.

    4. Hands-free Volume Setting


      1. A01610SE01

        Check the hands-free volume level.

        Screen Description
        Display Content
        *1: Receive voice level adjustment Setting possible for the voice level received from "Bluetooth" compatible phones.

        Note

        Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the receive voice quality is still acceptable after changing this setting.