NAVIGATION ECU REMOVAL


  1. EJECT MAP DISC


    1. Turn the engine switch on (ACC).

    2. A0162BCE01

      Apply protective tape to the places shown in the illustration.

    3. A01616U

      Insert 2 precision screwdrivers (φ1.5 or less) into the holes on both sides of the clock assembly at the angle shown in the illustration.

      Note

      Do not pry on the clock assembly with the screwdrivers as they may damage the clock assembly.

      Tech Tips

      If precision screwdrivers are not available, use in-vehicle tools (part No. 09135-53010).

    4. A0163G1E01

      Insert a protective taped screwdriver from the underside of the hazard switch and pull and remove the clock assembly.

      Note

      Do not pry on the hazard switch with the screwdriver as it may damage the switch.

    5. Remove the 2 precision screwdrivers.

    6. Push the "MENU" button.

    7. Touch "Map DVD" on the navigation screen.

    8. Touch "EJECT DVD" on the navigation screen to eject the map disc.

    9. Temporarily reinstall the clock assembly to make the removal of the multi-display assembly easier.

      Note

      Do not install the clock assembly completely because it will be removed later.

    10. Turn the engine switch off.

  2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A0161BO

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  3. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A016226

      Using a moulding remover, disengage the claw.

    2. A0161ZW

      Pull the upper No. 1 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  4. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A015YLQ

      Using a moulding remover, disengage the claw.

    2. A0160CR

      Pull the upper No. 2 console panel garnish in the direction indicated by the arrow to disengage the 2 clips and remove it.

  5. REMOVE CONSOLE PANEL SUB-ASSEMBLY


    1. A0160RU

      Hold the front of the console panel sub-assembly as shown in the illustration and disengage the 8 clips by pulling the console panel sub-assembly in the direction shown by the arrow.

      Note

      Do not use any tools to disengage the clips. The use of tools may result in damage to the console panel sub-assembly.

    2. Disconnect the connectors and remove the console panel sub-assembly.

  6. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. A0160IR

      Remove the 2 screws <E>.

    2. A0160OX

      Pull the front ash receptacle assembly in the direction indicated by the arrow to disconnect the connectors and remove it.

  7. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A0163DOE02

      Using a screwdriver, disengage the 4 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A015ZH6E03

      Apply protective tape to the areas shown in the illustration.

    3. A015ZAL

      Using a moulding remover, disengage the 4 claws starting from the right of the No. 3 instrument panel register assembly. Disengage the remaining 3 claws by pulling the No. 3 instrument panel register assembly by hand.

      Note

      Do not pry the lower part of the No. 3 instrument panel register assembly. Doing so may damage the assembly.

    4. Disconnect the connectors.

  8. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL


    1. A0160YT

      Disengage the 4 claws and remove the center lower instrument cluster finish panel.

  9. REMOVE MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY


    1. A0162FS

      Remove the 4 bolts.

    2. Pull the multi-display with radio receiver assembly toward the rear of the vehicle.

    3. Disconnect each connector and remove the multi-display.

  10. REMOVE NO. 1 RADIO BRACKET


    1. A015YV5

      Disengage the connector clamp.

    2. A0160LX

      Remove the 7 bolts and No. 1 radio bracket.

  11. REMOVE NO. 2 RADIO BRACKET


    1. A015Z6H

      Remove the 7 bolts and No. 2 radio bracket.

  12. REMOVE MULTI-DISPLAY ASSEMBLY


    1. A0161EJ

      Slide the multi-display assembly in the direction shown by the arrow to remove the multi-display assembly.

  13. REMOVE NAVIGATION ECU


    1. A0162FK

      Disconnect the connectors.

    2. A015ZE7

      Remove the 4 screws and navigation ECU.