LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (instrument panel junction block assembly) monitors communication between all the ECUs connected to the door system LIN bus lines. When the main body ECU (instrument panel junction block assembly) detects errors in communication with all the ECUs connected to the door system LIN bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be output.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (instrument panel junction block assembly) detects errors in communication with the ECUs connected to the door system LIN bus lines 3 times in a row.

  • Front power window regulator motor assembly LH*1

  • Front power window regulator motor assembly RH*2

  • Sliding roof ECU (Sliding roof drive gear sub-assembly)*3

  • Main body ECU (Instrument panel junction block assembly)

  • Wire harness

Tech Tips

*1: for LHD

*2: for RHD

*3: w/ Sliding Roof

WIRING DIAGRAM

A017EEHE07

INSPECTION PROCEDURE

Note

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

    Tech Tips

    *1: for LHD

    *2: for RHD

    *3: w/ Sliding Roof

    A017BNKE02

    1. Disconnect the D8 connector.

    2. Disconnect the H1*1or G10*2connector.

    3. Disconnect the Q12*3connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition

      D8-10 (LIN2) - H1*1-9 (LIN)

      		 Always Below 1 Ω

      D8-10 (LIN2) - G10*2-9 (LIN)

      		 Always Below 1 Ω

      D8-10 (LIN2) - Q12*3-4 (MPX1)

      		 Always Below 1 Ω
      D8-10 (LIN2) - Body ground Always 10 kΩ or higher

    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      D8-10 (LIN2) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. SYSTEM CHECK


    1. Check the vehicle specifications.

      Result
      Result Proceed to
      Models with Sliding roof A
      Models without Sliding roof B

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH*1/RH*2 Click here

    A

  3. CHECK FOR DTC (SLIDING ROOF ECU)

    Tech Tips

    *1: for LHD

    *2: for RHD


    1. Connect the D8 connector.

    2. Connect the H1*1or G10*2connector.

    3. Check for DTC.

      Result
      Result Proceed to
      B2325 is output A
      B2325 is not output B

    B

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here

    A

  4. CHECK FOR DTC (POWER WINDOW ECU)

    Tech Tips

    *1: for LHD

    *2: for RHD

    *3: w/ Sliding Roof


    1. Connect the Q12*3connector.

    2. Disconnect the H1*1or G10*2connector.

    3. Recheck for DTC.

      Result
      Result Proceed to
      B2325 is output A
      B2325 is not output (for LHD) B
      B2325 is not output (for RHD) C

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    A

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH*1/RH*2

    Tech Tips

    *1: for LHD

    *2: for RHD


    1. Replace the front power window regulator motor assembly LH*1or RH*2with a normally-functioning or a new one Click here.


    NEXT

  6. CHECK FOR DTC


    1. Recheck for DTC.

      Result
      Result Proceed to
      B2325 is not output A
      B2325 is output B

    B

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

    A

    END