FUEL LID LOCK CONTROL INSTALLATION


  1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    1. Engage the 9 clamp and install the fuel lid lock control cable sub-assembly.

      A017G52
    2. A017FEW

      Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

    3. A017EGB

      Connect the fuel lid lock control cable sub-assembly.

  2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    1. Engage the 11 clamps.

      A017B27
    2. A017FEW

      Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

    3. A017FRL

      Connect the fuel lid lock control cable sub-assembly.

  3. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A017BFM

      Install the fuel lid lock open lever sub-assembly with the 2 screws.

  4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly LH with the 2 bolts.

      A017FE0

  5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017FLFE01

      Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  6. INSTALL FRONT DECK SIDE TRIM COVER LH


    1. A017EJB

      Engage the 4 claws and install the 2 front deck side trim covers LH.

  7. INSTALL NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Install the No. 2 deck side trim hook with the screw.

  8. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    1. A017D0J

      for Front Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

    2. A017DHF

      for Rear Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

  9. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Engage the 10 claws and install the rear deck trim cover.

  10. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Engage the 5 claws and install the reclining remote control bezel LH.

  11. INSTALL REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Engage the 2 claws and install the rear power outlet socket cover.

  12. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    1. A017BVH

      Engage the claw and install the rear power point socket assembly.

    2. Connect the connector.

  13. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017BGW

      Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

  14. INSTALL SIDE TRIM COVER LH


    1. A017EO1

      Engage the 10 claws and install the side trim cover LH.

  15. INSTALL DECK SIDE TRIM LH


    1. A017BAR

      Engage the 3 guides and 4 claws as shown in the illustration.

    2. A017F36

      Install the deck side trim LH with the bolt.

  16. INSTALL DECK SIDE TRIM COVER NO.2


    1. A017BA5

      Engage the 2 claws and install the deck side trim cover LH.

  17. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RHD)


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly RH with the 3 bolts.

      A017FTC

  18. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  19. INSTALL FRONT DECK SIDE TRIM COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  20. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RHD)

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  21. INSTALL ROPE HOOK ASSEMBLY (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  22. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RHD)


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  23. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  24. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  25. INSTALL DECK SIDE TRIM RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  26. INSTALL DECK SIDE TRIM COVER NO.1 (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  27. INSTALL REAR SEAT SIDE GARNISH CAP (for RHD without Rear Air Conditioning System)


    1. A017FDU

      Engage the guide and the 8 claws, and install the rear seat side garnish cap.

  28. INSTALL REAR SEAT SIDE GARNISH CAP (for RHD with Rear Air Conditioning System)


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  29. INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  30. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  31. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  32. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)


    1. Install the rear seat lap type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  33. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  34. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Install the rear deck floor box with the 2 nuts.

  35. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017FMA

      Install the 2 nuts and the deck floor board assembly.

    2. Engage the 3 claws.

  36. INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  37. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  38. INSTALL DECK SIDE TRIM BOX LH


    1. Install the deck side trim box LH as shown in the illustration.

      A017CIY
    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  39. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  40. INSTALL DECK SIDE TRIM BOX RH


    1. Install the deck side trim box RH as shown in the illustration.

      A017EFK
    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  41. INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  42. INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  43. INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  44. INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  45. INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  46. INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  47. INSTALL JACK CARRIER SUPPORT

  48. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  49. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

  50. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  51. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  52. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  53. INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  54. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A017G6U

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  55. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A017CGP

      Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.

  56. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017F49E01

      Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  57. INSTALL REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  58. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017EEJE01

      Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  59. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  60. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)


    1. A017G6U

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  61. INSTALL LOWER CENTER PILLAR GARNISH RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  62. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)


    1. A017FFPE01

      Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  63. INSTALL REAR DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  64. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)


    1. A017D8ZE01

      Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  65. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  66. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. A017FCR

      Temporarily install the 2 bolts on the front side of the seat.

    2. A017BHD

      Temporarily install the 3 bolts on the rear side of the seat.

    3. Install the rear No. 1 seat assembly with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  67. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. Remove the rear seat reclining control cable from the carpet hole.

      A017DSHE01

    2. Connect the rear seat reclining control cable as shown in the illustration.

    3. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

      A017BYUE01
    4. A017EVX

      Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Return the seatback to the upright position.

    6. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A017ENNE01

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compress.

  68. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  69. INSTALL REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Engage the clip.

    2. Engage the 3 claws and install the rear seat leg side cover.

  70. INSTALL REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Engage the 4 claws and install the rear inner track bracket cover.

  71. INSTALL REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Engage the 4 claws and install the rear outer track bracket cover.

  72. INSTALL REAR SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Engage the 8 claws and install the 2 rear seat track bracket covers.

  73. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

  74. INSTALL REAR CENTER SEAT ASSEMBLY

  75. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    1. A017D5O

      Temporarily install the 2 bolts on the front side of the seat.

    2. A017EZ3

      Temporarily Install the 3 bolts on the rear side of the seat.

    3. Install the rear No. 1 seat assembly with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  76. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  77. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  78. INSTALL REAR SEAT LEG SIDE COVER RH


    1. A017F28

      Engage the clip.

    2. Engage the 3 claws and install the rear seat leg side cover.

  79. INSTALL REAR INNER TRACK BRACKET COVER RH


    1. A017F59

      Engage the 4 claws and install the rear inner track bracket cover.

  80. INSTALL REAR OUTER TRACK BRACKET COVER RH


    1. A017D2L

      Engage the 4 claws and install the rear outer track bracket cover.

  81. INSTALL REAR SEAT TRACK BRACKET COVER RH


    1. A017ERX

      Engage the 8 claws and install the 2 seat track bracket covers.

  82. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

  83. INSTALL FRONT SEAT ASSEMBLY LH (for LHD Manual Seat)


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Temporarily install the front seat assembly with the 4 bolts.

    4. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    5. A017D8FE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    6. Lift up the seat track adjusting handle and move the seat to the foremost position.

    7. A017G32E01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  84. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for LHD Manual Seat)


    1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.

      If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.

  85. INSTALL REAR SEAT TRACK COVER LH (for LHD Manual Seat)


    1. A017CWY

      Engage the 4 claws and install the 2 rear seat track covers.

  86. INSTALL FRONT INNER SEAT TRACK COVER LH (for LHD Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    2. A017DLZ

      Engage the 2 claws and install the front inner seat track cover.

  87. INSTALL FRONT OUTER SEAT TRACK COVER LH (for LHD Manual Seat)


    1. A017FOO

      Engage the 2 claws and install the front outer seat track cover.

  88. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD Manual Seat)

  89. INSTALL FRONT SEAT ASSEMBLY LH (for LHD Power Seat)


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Connect the cable to the negative (-) battery terminal.

      Note

      When reconnected the cable, some systems need to be initialized Click here.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the power seat switch knob and move the seat to the rearmost position.

    6. A017FKLE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    7. Operate the power seat switch knob and move the seat to the foremost position.

    8. A017B0KE01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  90. INSTALL REAR INNER SEAT TRACK COVER LH (for LHD Power Seat)


    1. A017DBE

      Engage the 2 claws and install the rear inner seat track cover.

  91. INSTALL REAR OUTER SEAT TRACK COVER LH (for LHD Power Seat)


    1. A017DLU

      Engage the 2 claws and install the rear outer seat track cover.

  92. INSTALL FRONT INNER SEAT TRACK COVER LH (for LHD Power Seat)


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017F34

      Engage the 2 claws and install the front inner seat track cover.

  93. INSTALL FRONT OUTER SEAT TRACK COVER LH (for LHD Power Seat)


    1. A017ET7

      Engage the 2 claws and install the front outer seat track cover.

  94. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD Power Seat)

  95. INSTALL FRONT SEAT ASSEMBLY RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  96. INSTALL FRONT SEAT SLIDE ADJUSTER LOCK (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  97. INSTALL REAR SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  98. INSTALL FRONT INNER SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  99. INSTALL FRONT OUTER SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  100. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD Manual Seat)

  101. INSTALL FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  102. INSTALL REAR INNER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  103. INSTALL REAR OUTER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  104. INSTALL FRONT INNER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  105. INSTALL FRONT OUTER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  106. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD Power Seat)

  107. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  108. INSPECT FRONT SEAT ASSEMBLY LH (for LHD Power Seat)


    1. Inspect the power seat operation.

    2. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the ignition switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  109. INSPECT FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  110. INSPECT SRS WARNING LIGHT

    Click here