FUEL LID LOCK CONTROL REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LHD Manual Seat)

  3. REMOVE FRONT OUTER SEAT TRACK COVER LH (for LHD Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    2. A017FOO

      Disengage the 2 claws and remove the front outer seat track cover.

  4. REMOVE FRONT INNER SEAT TRACK COVER LH (for LHD Manual Seat)


    1. A017DLZ

      Disengage the 2 claws and remove the front inner seat track cover.

  5. REMOVE REAR SEAT TRACK COVER LH (for LHD Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the foremost position.

    2. A017CWY

      Disengage the 4 claws and remove the 2 rear seat track covers.

  6. REMOVE FRONT SEAT ASSEMBLY LH (for LHD Manual Seat)


    1. A017G32

      Remove the 2 bolts on the rear side of the seat.

    2. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    3. A017D8F

      Remove the 2 bolts on the front side of the seat.

    4. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

    5. Disconnect the connectors under the front seat assembly.

    6. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LHD Power Seat)

  8. REMOVE FRONT OUTER SEAT TRACK COVER LH (for LHD Power Seat)


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017ET7

      Disengage the 2 claws and remove the front outer seat track cover.

  9. REMOVE FRONT INNER SEAT TRACK COVER LH (for LHD Power Seat)


    1. A017F34

      Disengage the 2 claws and remove the front inner seat track cover.

  10. REMOVE REAR OUTER SEAT TRACK COVER LH (for LHD Power Seat)


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A017DLU

      Disengage the 2 claws and remove the rear outer seat track cover.

  11. REMOVE REAR INNER SEAT TRACK COVER LH (for LHD Power Seat)


    1. A017DBE

      Disengage the 2 claws and remove the rear inner seat track cover.

  12. REMOVE FRONT SEAT ASSEMBLY LH (for LHD Power Seat)


    1. A017B0K

      Remove the 2 bolts on the rear side of the seat.

    2. Operate the power seat switch knob and move the seat to the rearmost position.

    3. A017FKL

      Remove the 2 bolts on the front side of the seat.

    4. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying Click here.

      • If the side airbag was deployed, replace the front seat assembly with a new one.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. Disconnect each connector under the front seat assembly.

    7. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  13. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  14. REMOVE FRONT OUTER SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  15. REMOVE FRONT INNER SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  16. REMOVE REAR SEAT TRACK COVER RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  17. REMOVE FRONT SEAT ASSEMBLY RH (for RHD Manual Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  18. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  19. REMOVE FRONT OUTER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  20. REMOVE FRONT INNER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  21. REMOVE REAR OUTER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  22. REMOVE REAR INNER SEAT TRACK COVER RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  23. REMOVE FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  24. REMOVE REAR CENTER SEAT ASSEMBLY

  25. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  26. REMOVE REAR SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  27. REMOVE REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Disengage the 4 claws and remove the rear outer track bracket cover.

  28. REMOVE REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Disengage the 4 claws and remove the rear inner track bracket cover.

  29. REMOVE REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  30. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A017BM1E01
    2. A017BWQE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A017BFVE01

    4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

      A017FFKE01

    6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

  31. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. A017BHD

      Remove the 3 bolts on the rear side of the seat.

    2. A017FCR

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  32. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

  33. REMOVE REAR SEAT TRACK BRACKET COVER RH


    1. A017ERX

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  34. REMOVE REAR OUTER TRACK BRACKET COVER RH


    1. A017D2L

      Disengage the 4 claws and remove the rear outer track bracket cover.

  35. REMOVE REAR INNER TRACK BRACKET COVER RH


    1. A017F59

      Disengage the 4 claws and remove the rear inner track bracket cover.

  36. REMOVE REAR SEAT LEG SIDE COVER RH


    1. A017F28

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  37. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  38. REMOVE REAR NO. 1 SEAT ASSEMBLY RH


    1. A017EZ3

      Remove the 3 bolts on the rear side of the seat.

    2. A017D5O

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  39. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A017B6P

      Disengage the 8 claws and guide, and remove the front door scuff plate LH.

  40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    1. A017G5W

      Remove the front door opening trim weatherstrip LH.

  41. REMOVE REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  42. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017C1V

      Remove the rear door opening trim weatherstrip LH.

  43. REMOVE LOWER CENTER PILLAR GARNISH LH (for LHD)


    1. A017F82

      Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.

  44. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (for LHD)


    1. A017G6U

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  45. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  46. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  47. REMOVE REAR DOOR SCUFF PLATE RH (for RHD)


    1. A017D4T

      Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  48. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)


    1. A017C1V

      Remove the rear door opening trim weatherstrip LH.

  49. REMOVE LOWER CENTER PILLAR GARNISH RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  50. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  51. REMOVE DECK BOARD ASSEMBLY


    1. A017CPI

      Remove the deck board assembly.

  52. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  53. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  54. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  55. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.

  56. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Disengage the 2 clips and remove the rear seat side cover LH.

  57. REMOVE DECK SIDE TRIM BOX LH


    1. A017BZVE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box LH as shown in the illustration.

      A017G2A

  58. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Disengage the 2 clips and remove the rear seat side cover RH.

  59. REMOVE JACK CARRIER SUPPORT

  60. REMOVE JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Remove the jack carrier cushion.

  61. REMOVE JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Remove the jack carrier cushion.

  62. REMOVE JACK ASSEMBLY (for LHD)


    1. A017EKS

      Remove the jack assembly.

  63. REMOVE JACK ASSEMBLY (for RHD)


    1. A017DSX

      Remove the jack assembly.

  64. REMOVE JACK CARRIER ASSEMBLY (for LHD)


    1. A017EAS

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  65. REMOVE JACK CARRIER ASSEMBLY (for RHD)


    1. A017D6R

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  66. REMOVE DECK SIDE TRIM BOX RH


    1. A017FOPE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box RH as shown in the illustration.

      A017E9B

  67. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017G15

      Remove the 4 bolts and 4 nuts.

    2. Remove the deck floor board assembly.

  68. REMOVE REAR MAT


    1. A017F51

      Remove the rear mat.

  69. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017FMA

      Disengage the 3 claws.

    2. Remove the 2 nuts and the deck floor board assembly.

  70. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Remove the 2 nuts and the deck floor box.

  71. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Remove the bolt and rear No. 2 seat inner belt assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  72. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Remove the bolt and disconnect the rear seat lap type belt assembly LH.

  73. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  74. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Remove the 4 bolts and the rear No. 2 seat assembly.

  75. REMOVE REAR FLOOR FINISH PLATE


    1. A017BSY

      Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.

  76. REMOVE DECK SIDE TRIM COVER NO.2


    1. A017FRQE01

      Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  77. REMOVE DECK SIDE TRIM LH


    1. A017EO1

      Disengage the 10 claws and remove the side trim cover LH.

  78. REMOVE SIDE TRIM COVER LH


    1. A017EO1

      Disengage the 10 claws and remove the side trim cover LH.

  79. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017EUZE01

      Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  80. REMOVE REAR POWER POINT SOCKET ASSEMBLY


    1. Disconnect the connector.

    2. A017G8M

      Disengage the claw and remove the rear power point socket assembly.

  81. REMOVE REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Disengage the 2 claws and remove the rear power outlet socket cover.

  82. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Disengage the 10 claws and remove the rear deck trim cover.

  83. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Disengage the 5 claws and remove the reclining remote control bezel LH.

  84. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. A017FLCE01

      for Front Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and the rope hook assembly.

    2. A017B9EE01

      for Rear Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and rope hook assembly.

  85. REMOVE NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Remove the screw and the No. 2 deck side trim hook.

  86. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. A017C3ZE01

      Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

      Tech Tips

      Tape the screwdriver tip before use.

  87. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017ETD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  88. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 bolts.

    2. Remove the 2 clips.

    3. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

      A017FE0

  89. REMOVE REAR SEAT SIDE GARNISH CAP (for RHD without Rear Air Conditioning System)


    1. A017DMI

      Disengage the 8 claws and guide, and remove the rear seat side garnish cap.

  90. REMOVE REAR SEAT SIDE GARNISH CAP (for RHD with Rear Air Conditioning System)


    1. A017FP0

      Remove the screw.

    2. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.

  91. REMOVE DECK SIDE TRIM COVER NO.1 (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  92. REMOVE DECK SIDE TRIM RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  93. REMOVE SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)


    1. A017CSI

      Disengage the 4 claws and remove the side trim cover RH.

  94. REMOVE REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)


    1. A017B3P

      Disengage the 4 claws and remove the rear room temperature sensor.

    2. Disconnect the connector.

  95. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH (for RHD)


    1. A017BZ2E01

      Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

      Tech Tips

      Tape the screwdriver tip before use.

  96. REMOVE ROPE HOOK ASSEMBLY (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  97. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RHD)

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  98. REMOVE FRONT DECK SIDE TRIM COVER RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  99. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  100. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RHD)


    1. Remove the 3 bolts.

    2. Remove the 2 clips.

    3. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

      A017FTC

  101. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A017GBF

      Remove the 2 screws.

    2. Remove the fuel lid lock open lever sub-assembly as shown in the illustration.

  102. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    1. A017EGB

      Disconnect the fuel lid lock control cable sub-assembly.

    2. A017BRG

      Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.

    3. Disengage the 9 clamps and remove the fuel lid lock control cable sub-assembly.

      A017G52

  103. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    1. A017FRL

      Disconnect the fuel lid lock control cable sub-assembly.

    2. A017BRG

      Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.

    3. Disengage the 11 clamps and remove the fuel lid lock control cable sub-assembly.

      A017B27