Click here

FRONT DOOR BLACK OUT TAPE REMOVAL

Click here
Click here
  1. Click here

    DISCONNECT NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A017CI2

      Disengage the claw and clip, and remove the front door lower frame bracket garnish.

  3. Click here

    REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.

  4. Click here

    REMOVE FRONT ARMREST UPPER BASE PANEL


    1. A017FEPE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 7 claws and clip, and remove the front armrest upper base panel.

    2. Disconnect the connector.

  5. Click here

    REMOVE ASSIST GRIP COVER


    1. A017EAME01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the assist grip cover.

  6. Click here

    REMOVE COURTESY LIGHT ASSEMBLY


    1. A017DZME01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  7. Click here

    REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017FDZ

      Remove the 3 screws.

    2. A017FU9

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

    4. A017EHB

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and front door inside locking cable.

    6. Disconnect the connector.

  8. Click here

    REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A017ESJ

      Remove the front door inner glass weatherstrip from the front door panel.

  9. Click here

    REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    1. A017BR7

      Disconnect the connector.

    2. Remove the 4 bolts and front No. 1 speaker assembly.

      Note:

      Do not touch the cone part of the speaker.

  10. Click here

    REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER


    1. A017CEJE01

      Disconnect the connector and clamp.

    2. Disengage the clip.

    3. A017FZC

      Remove the 3 nuts.

    4. Disengage the claw and remove the outer rear view mirror assembly with cover.

  11. Click here

    REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A017DHL

      Disconnect the each connector and 2 clamps, and remove the front door service hole cover.

      Tip:

      Remove the remaining butyl tape on the door side.

  12. Click here

    REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A017E3V

      Remove the hole plug.

    2. Connect the negative battery terminal.

    3. Connect the power window regulator motor connector.

    4. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    5. Disconnect the negative battery terminal and power window regulator master switch assembly.

    6. Disconnect the power window regulator motor connector.

    7. A017FOD

      Remove the 2 bolts.

      Note:

      After the bolts are removed, do not allow the door to fall.

    8. A017D4SE01

      Remove the front door glass sub-assembly as shown in the illustration.

      Note:

      Do not damage the door glass.

  13. Click here

    REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A017F87E01

      Loosen the temporary bolt.

      Note:

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

    4. Remove the temporary bolt from the front door window regulator sub-assembly.

  14. Click here

    REMOVE FRONT DOOR GLASS RUN


    1. A017BGI

      Remove the front door glass run.

  15. Click here

    REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    1. A017BYAE01

      Put protective tape around the front door belt moulding assembly.

    2. A017G7M

      Disengage the 6 claws and remove the front door belt moulding assembly.

      Note:

      Be careful when removing the moulding as there are claws attached to the front and rear ends of the moulding.

  16. Click here

    REMOVE DOOR FRAME GARNISH


    1. A017FQL

      Disengage the clip and remove the door frame garnish.

      Tip:

      This clip needs to be replaced with a new one because the clip will break when removing the door frame garnish.

  17. Click here

    REMOVE FRONT DOOR WEATHERSTRIP


    1. A017BBY

      Remove the upper part of the front door weatherstrip to the extent that allows removal of the black out tape.

  18. Click here

    REMOVE NO. 1 BLACK OUT TAPE


    1. Using a heat light, heat the No. 1 black out tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the No. 1 black out tape and pull it parallel to the vehicle body to pull it off.

  19. Click here

    REMOVE INNER UPPER BLACK OUT FRONT DOOR TAPE


    1. Using a heat light, heat the inner upper black out front door tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the inner upper black out front door tape and pull it parallel to the vehicle body to pull it off.

  20. Click here

    REMOVE INNER REAR BLACK OUT FRONT DOOR TAPE


    1. Using a heat light, heat the inner rear black out front door tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the inner rear black out front door tape and pull it parallel to the vehicle body to pull it off.