REAR DOOR BELT MOULDING INSTALLATION


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A017CT3

      Engage the 6 claws and install the rear door belt moulding assembly.

  2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

    2. A017B2YE02

      Install the temporary bolt to the rear door window regulator sub-assembly.

    3. Temporarily install the window regulator.

    4. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Connect the connector.

  3. INSTALL REAR DOOR GLASS RUN


    1. A017BMF

      Install the rear door glass run.

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A017B5Q

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A017G2W

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door glass run to the rear door lower window frame sub-assembly.

    3. A017ECI

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

    4. A017FHT

      Install the rear door vent seal.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A017FALE01

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

    4. Connect the connector.

  8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Install the rear door inner glass weatherstrip.

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017CXI

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

    2. Engage the 2 clamps.

    3. A017GAC

      Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.

    4. Engage the 9 clips and install the rear door trim board to the rear door panel.

    5. A017F2KE01

      Install the 2 screws <B>.

    6. Install the screw <A>.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  10. INSTALL DOOR ASSIST GRIP COVER


    1. A017C7J

      Engage the 4 claws and install the door assist grip cover.

  11. INSTALL REAR DOOR ARMREST UPPER BASE PANEL


    1. Connect the connector.

    2. A017DAJ

      Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.

  12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A017ERK

      Engage the 3 claws to install the rear door inside handle bezel plug.

  13. CONNECT NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.