Click here

REAR DOOR BELT MOULDING REMOVAL

Click here
Click here
  1. Click here

    DISCONNECT NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.

  3. Click here

    REMOVE REAR DOOR ARMREST UPPER BASE PANEL


    1. A017EWNE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

    2. Disconnect the connector.

  4. Click here

    REMOVE DOOR ASSIST GRIP COVER


    1. A017D3PE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  5. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017F2K

      Remove the 3 screws.

    2. A017GAC

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

    4. A017EA4

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and rear door inside locking cable.

  6. Click here

    REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Remove the rear door inner glass weatherstrip from the rear door panel.

  7. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER


    1. A017D47

      Disconnect the connector.

    2. Remove the rear door service hole cover.

      Tip:

      Remove the remaining tape on the door.

  8. Click here

    REMOVE REAR DOOR GLASS RUN


    1. A017BMF

      Remove the rear door glass run.

  9. Click here

    REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A017FHT

      Remove the rear door vent seal.

    2. A017ECI

      Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.

  10. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A017E81

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  11. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A017F6A

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note:

      Do not damage the door glass.

  12. Click here

    REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A017C3NE01

      Connect the positive (+) lead of the battery to terminal 2, and the negative (-) lead to terminal 1 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.

    2. A017ETW

      Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.

  13. Click here

    REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    1. A017BU7E01

      Put protective tape around the rear door belt moulding assembly.

    2. A017CT3

      Disengage the 6 claws and remove the rear door belt moulding assembly.

      Note:

      Be careful when removing the moulding as there are claws attached to the front end of the moulding.