FRONT DOOR BELT MOULDING INSTALLATION


  1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    1. A017G7M

      Engage the 6 claws and install the front door belt moulding assembly.

  2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

    2. A017F87E02

      Install the temporary bolt to the front door window regulator sub-assembly.

    3. Temporarily install the window regulator.

    4. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. A017CPJE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

    2. A017FOD

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A017E3V

      Install the hole plug.

  4. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.

    3. A017G5FE01

      Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover avoiding wrinkles and air bubbles.

    4. A017DHL

      Connect each connector.

    5. Engage the 2 clamps.

  5. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER


    1. A017FZCE01

      Engage the claw, and temporarily install the outer rear view mirror assembly with cover.

    2. Tighten the 3 nuts in the order shown in the illustration to install the outer rear view mirror assembly with cover.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A017CEJ

      Engage the clamp and connect the connector.

    4. Install the clip.

  6. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    1. A017BR7

      Install the front No. 1 speaker assembly with the 4 bolts.

      Note

      Do not touch the cone part of the speaker.

    2. Connect the connector.

  7. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A017ESJ

      Install the front door inner glass weatherstrip.

  8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. Connect the connector.

    2. A017F3J

      Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

    3. Engage the 2 clamps.

    4. A017FU9

      Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

    5. Engage the 9 clips.

    6. A017FDZE01

      Install the 2 screws <B>.

    7. Install the screw <A> and front door trim board to the front door panel.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  9. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A017CHJ

      Engage the claw and install the courtesy light assembly.

  10. INSTALL ASSIST GRIP COVER


    1. A017EGS

      Engage the 4 claws and install the assist grip cover.

  11. INSTALL FRONT ARMREST UPPER BASE PANEL


    1. Connect the connector.

    2. A017DCH

      Engage the 7 claws and clip and install the front armrest upper base panel.

  12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A017ERK

      Engage the 3 claws and install the front door inside handle bezel plug.

  13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A017CI2

      Engage the clip and claw, and install the front door lower frame bracket garnish.

  14. CONNECT NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

    Click here