Click here

BACK WINDOW SUPPORT INSTALLATION

Click here
Click here
  1. Click here

    PRECAUTION

    Note:

    • If a back window stay assembly is removed and installed, the location of the axis of the rear wiper motor assembly will change, causing the wiping angle to change. Be sure to remove and install the rear wiper motor assembly using the centering jig.

    • After installing a back window stay assembly, install the rear wiper motor assembly. Do not open the glass hatch before installing the rear wiper link pivot.

  2. Click here

    INSTALL BACK WINDOW STAY BOLT


    1. When replacing the back window stay bolt with a new one:


      1. Clean the threaded surface on the vehicle body with a non-residue solvent.

      2. A017EWU

        Install the back window stay bolt.

        22 N*m 224 kgf*cm 16 ft.*lbf

    2. When reusing the back window stay bolt:


      1. Clean the threaded surface on the vehicle body with a non-residue solvent.

      2. Apply adhesive to the threads of the back window stay bolt.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      3. A017EWU

        Install the back window stay bolt.

        22 N*m 224 kgf*cm 16 ft.*lbf
  3. Click here

    INSTALL BACK WINDOW STAY ASSEMBLY

    Note:

    • Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.

    • Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the piston rod and result in gas leaks.

    • Do not apply any horizontal load to the cylinders in the in order to prevent the piston rod from deforming.


    1. When replacing the back window stay assembly with a new one:


      1. A017BEE

        Install the 2 stop rings to the back window stay assembly.

    2. A017FLL

      Install the back window stay assembly.

      Note:

      Install the back door stay assembly while supporting the back door by hand.

    3. Check that the hood support assembly is engaged in the ball joint and that the hood support assembly cannot be pulled out.

  4. Click here

    REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.

  5. Click here

    REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  6. Click here

    REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Disengage the 6 claws, and remove the back door service hole cover LH.

  7. Click here

    DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Disconnect the power back door rod and remove the back door stay plate.

  8. Click here

    REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  9. Click here

    REMOVE BACK DOOR TRIM COVER RH


    1. A017D6U

      Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.

  10. Click here

    REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)


    1. A017G02

      Disengage the 2 claws and 4 guides, and remove the back door lock cover.

  11. Click here

    REMOVE ASSIST STRAP HOLE COVER


    1. A017CPS

      Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.

  12. Click here

    REMOVE ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Remove the bolt and assist strap assembly.

  13. Click here

    REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Disengage the 16 clips and remove the back door trim panel assembly.

  14. Click here

    REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. A017G4Z

      Disengage the 3 clips and remove the rear wiper shaft cover.

  15. Click here

    REMOVE REAR WIPER ARM HEAD CAP


    1. A017DOH

      Remove the rear wiper arm head cap.

  16. Click here

    REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. A017BYQ

      Remove the nut and the rear wiper arm and blade assembly.

  17. Click here

    REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A017ESU

      Remove the rear wiper link cap.

  18. Click here

    REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type)


    1. A017CYL

      Remove the nut and the rear wiper link pivot.

  19. Click here

    REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. When reinstalling the rear wiper motor assembly:


      1. Open the glass hatch.

      2. A017B51

        Engage the 3 claws and 2 guides, and then install the centering jig.

        Note:

        • The centering jig cannot be reused.

        • Do not remove the centering jig before installing the rear wiper link pivot.

      3. A017EGY

        Close the glass hatch, and engage the 2 claws and guide.

        Note:

        Be sure to engage the 2 claws and guide securely.

      4. A017CCB

        Disconnect the connector.

      5. Remove the 2 nuts.

      6. Remove the 4 bolts and the rear wiper motor assembly.

        Note:

        • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

        • Be careful not to scratch the back door glass.

    2. When using a new rear wiper motor assembly:


      1. A017ET9

        Disconnect the connector.

      2. Remove the 4 bolts.

      3. A017FDH

        Remove the 2 nuts and the rear wiper motor assembly.

        Note:

        Be careful not to scratch the back door glass.

  20. Click here

    INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. A017CCBE01

      Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

      Note:

      • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

      • Be careful not to scratch the back door glass.

      • Do not remove the centering jig before installing the rear wiper link pivot.

    2. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

      Bolt
      5.5 N*m 56 kgf*cm 49 in.*lbf
      Nut
      8.0 N*m 82 kgf*cm 71 in.*lbf

    3. Connect the connector.

  21. Click here

    INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)


    1. A017CYL

      Install the rear wiper link pivot with the nut.

      7.0 N*m 71 kgf*cm 62 in.*lbf

    2. Open the glass hatch.

    3. A017B51

      Disengage the 2 guides.

    4. Disengage the 3 claws and remove the centering jig.

    5. Close the glass hatch.

  22. Click here

    INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A017FA7E01

      Apply MP grease to the entire surface of the rear wiper link cap.

      Tip:

      Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

    2. A017ESU

      Install the rear wiper link cap.

  23. Click here

    INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)


    1. Stop the wiper motor at the automatic stop position.

    2. A017C5CE01

      When reinstalling:


      1. Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017BKPE01

      Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

      Area Dimension
      A 10 mm (0.39 in.)

    4. Install the rear wiper arm and blade assembly with the nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
      Tip:

      Hold down the wiper arm by hand when tightening the nut.

  24. Click here

    INSTALL REAR WIPER ARM HEAD CAP


    1. A017DOH

      Install the rear wiper arm head cap.

      Tip:

      Push down on the cap until a click sound can be heard.

  25. Click here

    INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. Open the glass hatch.

    2. A017G4Z

      Engage the 3 clips and install the rear wiper shaft cover.

    3. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.

  26. Click here

    INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Engage the 16 clips and install the back door trim panel assembly.

  27. Click here

    INSTALL ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Install the assist strap assembly with the bolt.

  28. Click here

    INSTALL ASSIST STRAP HOLE COVER


    1. A017CPS

      Engage the 2 guides and 2 claws, and install the assist strap hole cover.

  29. Click here

    INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type)


    1. A017G02

      Engage the 4 guides and 2 claws, and install the back door lock cover.

  30. Click here

    INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  31. Click here

    INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  32. Click here

    CONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Install the back door stay plate and connect the power back door rod.

      18 N*m 184 kgf*cm 13 ft.*lbf
  33. Click here

    INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Engage the 6 claws and install the back door service hole cover LH.

  34. Click here

    INSTALL BACK DOOR TRIM COVER RH


    1. A017D6U

      Engage the 2 clips and 2 claws, and install the back door trim cover RH.

  35. Click here

    INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.